Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
Search Results "Tape Measure"
-
1133A.2.1 Clear width
-
M302.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
The running slope of ramps and bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail...
-
§ 36.304(d)(4) Exemption for small facilities
For measures taken to comply with the barrier removal requirements of this section, existing facilities shall comply with the applicable requirements for alterations in § 36.402 and §§ 36.404...
-
7(2)(b)(vi)
(vi) Bathtubs and tub/showers located in the bathroom provide a clear access aisle adjacent to the lavatory that is at least 2'6" wide and extends for a length of 4'0" (measured from the...
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
§ 38.119(a)
(a) Any stepwell, or doorway with a lift, ramp or bridge plate, shall have, when the door is open, at least 2 foot-candles of illumination measured on the step tread, ramp, bridge plate...
-
§ 38.81(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured on the...
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
604.9.3 Height
The height of water closets shall be 11 inches (280 mm) minimum and 17 inches (430 mm) maximum measured to the top of the seat....
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
ASSESSMENT, PROGRESS, ACHIEVEMENT, AND GRADING
Assessment instruments that compare the individual against herself or himself are able to measure both attainment and growth....
-
III-4.4300 Standards to apply
Measures taken to remove barriers should comply with the ADA Accessibility Guidelines (ADAAG) contained in the appendix to the Department's rule....
-
Standardized Tests of Physical Fitness and Community Ambulation
Resting heart rate and energy consumption were measured with the subject seated or reclining on a couch. Heart rate was measured with a Polar heart rate monitor (Polar Vantage XL)....
-
What values are recommended for ground and floor surfaces along an accessible route?
In the study sponsored by the Access Board, laboratory measurements from a Kistler force plate and computer analysis of the gaits of persons with mobility impairments (including crutch users...
-
Capabilities, Resources, and Facilities
hands-on experience with the measurement of all classes of anthropometric dimensions. hands-on experience with experimental subjects and human use considerations....
-
4.5 Weight Scales
In certain circumstances, such as setting chemotherapy dosages, weight is often a critical measurement....
-
Test Procedures
Accessibility Measures All surfaces were measured with the rotational penetrometer periodically over the first 6 months of exposure (Fig. 9)....
-
B. Technical standards for criterion-related validity studies
The possibility of bias should be considered both in selection of the criterion measures and their application....
-
Access-Able Designs Tub Transfer Bench SH-414-2SDL
Measures 25" W x 15" D. Custom sizes available. 5 year warranty....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
