3.1 Definitions: 3.1.1 Terminology used in this practice conforms to the definitions included in Terminology E867. 3.1.1.1 longitudinal profile measurement, n—a series of elevation...
Search Results "Tape Measure"
-
3. Terminology
-
1015.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
- Better Living Curve Soap and Shower Dispenser 3
- Better Living Classic Soap Dispenser 1
- Better Living UNO Soap Dispenser
- Better Living Curve Soap Dispenser 1
- Better Living Ulti-Mate Soap and Shower Dispenser 3 with Mirror
- Better Living Signature Soap Dispenser 1
- Better Living Clear Choice Soap Dispenser 1
- SafePath EZCurb™ Wheelchair Ramps - Vertical Barrier Removal
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
1009.4.2 Height
The height of the transfer wall shall be 16 inches (405 mm) minimum and 19 inches (485 mm) maximum measured from the deck. Figure 1009.4.2 Transfer Wall Height...
-
Are transportation operators required to retrofit their vehicles to accommodate larger and heavier wheelchairs?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and the lift platform accommodates a wheelchair measuring 30 inches by 48 inches....
-
§ 35.150(b)(5) Exemption for small facilities
For measures taken to comply with the program accessibility requirements of this section, existing facilities shall comply with the applicable requirements for alterations in § 35.151 of...
-
Are transportation operators required to retrofit their vehicles to accommodate larger and heavier wheelchairs?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and the lift platform accommodates a wheelchair measuring 30 inches by 48 inches....
-
H25
Is the clear width of the door at least 32 inches (measured between the face of the door and the edge of the opening) when the door is open 90 degrees?...
-
G. Completing the Survey and Checklist
Completing the Survey and Checklist The survey and checklist forms will prompt you for what to look at and where to measure....
-
2.1.2.2 Additional Proposed Specifications (by Oval Window Audio)
Field Strength: As per IEC 118‒4, with the additional condition that the measurements be "A" weighted to disallow the influence of inaudible low frequency power line electrical noise....
-
M303.2.4.1.2 Height
Wheelchair spaces shall include toe clearance 9 inches (230 mm) high minimum above the floor measured to a depth of 6 inches (150 mm) maximum from the toe end of the wheelchair space....
-
10.3.2(4)
(4) In light rail, rapid rail and commuter rail key stations, the platform or a portion thereof and the vehicle floor shall be coordinated so that the vertical difference, measured when...
-
5. Significance and Use
5.1 This practice provides a means for obtaining a quantitative estimate of a surface property defined as roughness using longitudinal profile measuring equipment. 5.1.1 The PRI is portable...
-
1017.5 Tread Obstacles
Tread obstacles on trails, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
T502.4 Doorways with Steps on Over-the-Road Buses
The door opening clear width above a height of 48 inches (1220 mm) measured from the lowest step tread shall be permitted to taper so as to reduce in width to 18 inches (457 mm) minimum....
-
1017.5 Tread Obstacles
Tread obstacles on trails, passing spaces, and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....