hands-on experience with the measurement of all classes of anthropometric dimensions. hands-on experience with experimental subjects and human use considerations....
Search Results "Dimension Range"
-
Capabilities, Resources, and Facilities
-
Facility sell-out. (Section-by-Section Analysis)
Blocks of seats should be released in stages, and should include tickets in a range of price categories and locations that is representative of the range of seating that remains available...
-
Facility sell-out. (Section-by-Section Analysis)
Blocks of seats should be released in stages, and should include tickets in a range of price categories and locations that is representative of the range of seating that remains available...
-
11B-1009.2 Pool lifts
Pool lift seats that consist of materials that resist corrosion and provide a firm base to transfer will be usable by a wider range of people with disabilities....
-
Definition of "wheelchair." (Section-by-Section Analysis)
the dimensions of the ‘‘common wheelchair'' upon which the 2004 ADAAG was based....
-
302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Figure 302.3 Elongated Openings in Floor or Ground Surfaces...
-
1008.3.1.3 Transfer Space
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
Bus boarding and alighting areas
Bus boarding and alighting areas must be in compliance with the ADA-ABA Guidelines (Section 810.2), which address surfaces (sturdy), dimensions (96" long x 60" wide); connection to sidewalks...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
1008.3.1.3 Transfer Space
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308....
-
309.3 Height
Operable parts shall be placed within one or more of the reach ranges specified in 308....
-
4.31.3* Mounting Height
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6....
-
4.31.3* MOUNTING HEIGHT
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6....
-
Viewing Area
An outdoor space developed for viewing a landscape or point of interest such as a mountain range, a valley, or a waterfall....
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308....
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308....
-
F104.2 Calculation of Percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
10.3.1(17)
EXCEPTION: Elevator cars with a clear floor area in which a 60 inch diameter circle can be inscribed may be substituted for the minimum car dimensions of 4.10, Fig. 22....
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....