Controls shall be located within one of the reach ranges specified in Section 11B-308....
Search Results "Dimension Range"
Filters
Commonly Searched Documents
-
11B-411.4.6.1 Location
-
309.3 Height
Operable parts shall be placed within one or more of the reach ranges specified in 308....
-
4.31.3* Mounting Height
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6....
-
4.31.3* MOUNTING HEIGHT
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6....
-
Viewing Area
An outdoor space developed for viewing a landscape or point of interest such as a mountain range, a valley, or a waterfall....
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308....
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308....
-
Kompan, Inc. Solitaires Spinners - GXY926 - Miram Video
Made for older children and teenagers, Miram is part of Kompan's extensive range of novel, high quality playground equipment....
-
Expert Advice of Medical Practitioners
Based on her experience that the general range of customized manual wheelchair height is 15.5 inches- 19.5 inches and that power wheelchairs range from 16.5”- 22” high, she stated that the...
-
Measures and Procedures
Measures and Procedures A custom-built modular, transfer station was designed and built and consisted of a height adjustable platform capable of a range between 10” to 29” with increments...
-
Grab Bar Cross Sections
Non-circular cross sections were to have maximum cross section dimensions of 2 inches, a perimeter dimension between 4 and 4‒11/16 inches, and edges with a c inch minimum radius....
-
2.2 Key Measurement Variables and Procedures
Body and wheelchair dimensions: Approximately 125 locations of body and wheelchair points recorded in three dimensions. 3....
-
3. Flush valve
Flush valve is located in reach range and is operable without tight grasping, twisting, or pinching....
-
A Broad Definition of Disability Leaves No One Behind
Using a broad definition shows intent to include a broad range of people and leave no one behind....
-
4.31.7 Telephone Books
Telephone books, if provided, shall be located in a position that complies with the reach ranges specified in 4.2.5 and 4.2.6....
-
4.31.7 TELEPHONE BOOKS
Telephone books, if provided, shall be located in a position that complies with the reach ranges specified in 4.2.5 and 4.2.6....
-
SafePath: ADA Entry Level Landing Installation Training Video
requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface area in front of the door designed to specific dimensions...
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
5.8.2 Knee and Toe Clearance Under Breast Platform
The overall knee and toe space should be increased to a minimum of 28 inches deep, from the initially proposed 25 inch absolute dimension; increasing the knee clearance directly underneath...
-
4.4.2 Head Room
If vertical clearance of an area adjoining an accessible route is reduced to less than 80 in (nominal dimension), a barrier to warn blind or visually-impaired persons shall be provided (...
-
4.4.2 HEAD ROOM
If vertical clearance of an area adjoining an accessible route is reduced to less than 80 in (nominal dimension), a barrier to warn blind or visually-impaired persons shall be provided (...
-
4.10.9 Floor Plan of Elevator Cars
Acceptable door opening and inside dimensions shall be as shown in Fig. 22....
-
Dimensional Tolerances [3.2]
Recommendation: It is good practice to avoid specifying precisely to the maximum or minimum where possible so that achieved dimensions fall within ADAAG requirements....
