Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
Search Results "Dimension Range"
Filters
Commonly Searched Documents
-
104.2 Calculation of Percentages
-
302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Figure 302.3 Elongated Openings in Floor or Ground Surfaces ...
-
10.3.1(17)
EXCEPTION: Elevator cars with a clear floor area in which a 60 inch diameter circle can be inscribed may be substituted for the minimum car dimensions of 4.10, Fig. 22....
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
3.0 Comparison of Research Methodologies
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
Facility sell-out. (Section-by-Section Analysis)
Blocks of seats should be released in stages, and should include tickets in a range of price categories and locations that is representative of the range of seating that remains available...
-
Facility sell-out. (Section-by-Section Analysis)
Blocks of seats should be released in stages, and should include tickets in a range of price categories and locations that is representative of the range of seating that remains available...
-
11B-1009.2 Pool lifts
Pool lift seats that consist of materials that resist corrosion and provide a firm base to transfer will be usable by a wider range of people with disabilities....
-
Measuring Techniques
Software later allows the calculation of point-to-point distances and other dimensions....
-
11B-703.8.5 Character width
TABLE 11B-703.8.5 PIXEL COUNT FOR LOW RESOLUTION VMS SIGNAGE CHARACTER HEIGHT CHARACTER WIDTH RANGE STROKE WIDTH RANGE CHARACTER...
-
Example 1: With Cooking Facilities
With Cooking Facilities An employee break room with fixed or built-in range cooking facilities shall comply with the requirements of 212 and 804 for kitchens and kitchenettes....
-
11B-407.2.2.3 Audible signals
Existing elevators shall not be required to comply with the requirements for frequency and dB range of audible signals. ...
-
1008.3.1.3 Transfer Space
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
11B-1008.3.1.3 Transfer space
The 48 inch (1219 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
A. Slope at Door
If a fully automatic door is not provided, is the walkway in front of the lobby door level, without any portion steeper than 1:50 (critical dimension of ´" or less), so persons who use wheelchairs...
-
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis)
The 48-inch dimension is based on the length of a stationary occupied wheelchair. This side reach requirement mirrors existing 508 Standards § 1194.25(j)(1) and Figure 1....
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
R103.2 Calculation of Percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half is permitted....
-
Controls [4.21.5]
The dimensions for seats in 36 inch stalls are appropriate for seats in roll-in showers as well....
-
11B-1008.3.1.3 Transfer space
The 48 inch (1219 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
§ 38.23(b)(2)(ii) Exception
Where the lift is designed to deploy with its long dimension parallel to the vehicle axis and which pivots into or out of the vehicle while occupied (i.e., “rotary lift”), the requirements...
-
11B-1008.3.1.3 Transfer space
The 48 inch (1219 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....