"(29) However, recumbent bicycles, bicycles with trailers, and hand cycles all have 85th percentile lengths greater than 1.8 m (6 ft)....
Search Results "Segment Length"
-
Refuge Islands
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
Landings
Must be as wide as the ramp they connect to A minimum length of 60 inches (1525 mm) If ramps change direction, the minimum landing size must be 60 inches (1525 mm) wide...
-
407.12.3.1 Unobstructed Forward Reach
Where the operable part is located at the leading edge of the maximum protrusion within the length of the vertical reference plane of the ICT, the operable part shall be 48 inches (1220...
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
11B-1003.2.1 Boat slips
Exceptions: Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with Section 11B-1003.2...
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1.1.11 Ramp running slope
overall running slope of ramps by determining elevations at the top and bottom of the ramp at the midpoint of the width of each ramp run and calculate the slope using the horizontal ramp length...
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
Do the ACAA and its implementing regulations (14 CFR part 382 or part 382) apply to both U.S. and foreign carriers?
foreign air carriers is Section 382.70(b), which expressly requires foreign carriers to record, categorize, and report written disability-related complaints associated with any flight segment...
-
Designed Use
There is only one "Designed Use" per trail or trail segment....
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
Coverage and Definition of “Flight”
carrier operates a flight between two non-U.S. points and the flight carries the code of a U.S. carrier, the final rule will not extend coverage to the foreign carrier for that flight segment...
-
Resting Intervals on Trails
Provide resting intervals between each trail segment any time the running slope exceeds 1:20 (5 percent) as shown in table 5....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
Observations:
It would be very difficult for the occupant to have the powered device come to rest on a platform that is the exact length as its wheelbase or even a few inches more....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
B. Speaking, Listening, Reading, and Writing: When Auxiliary Aids and Services Must be Provided
The type of aid or service necessary depends on the length and complexity of the communication as well as the format....
-
§ 37.131(c) Fares
., without regard to discounts) for a trip of similar length, at a similar time of day, on the entity's fixed route system....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....