Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.12.3.2....
Search Results "Segment Length"
Filters
Commonly Searched Documents
-
407.12.3.2 Obstructed Forward Reach
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
11B-812.7 Access aisle
Access aisles shall be 60 inches (1524 mm) wide minimum and shall extend the full required length of the vehicle spaces they serve....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
Landings
Must be as wide as the ramp they connect to A minimum length of 60 inches (1525 mm) If ramps change direction, the minimum landing size must be 60 inches (1525 mm) wide...
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
407.12.3.1 Unobstructed Forward Reach
Where the operable part is located at the leading edge of the maximum protrusion within the length of the vertical reference plane of the ICT, the operable part shall be 48 inches (1220...
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
The National Association of Home Builders Certified Aging-in-Place Specialist (CAPS)
The Certified Aging-in-Place Specialist (CAPS) designation program teaches the technical, business management, and customer service skills essential to competing in the fastest growing segment...
-
Observations:
It would be very difficult for the occupant to have the powered device come to rest on a platform that is the exact length as its wheelbase or even a few inches more....
-
1.1.11 Ramp running slope
overall running slope of ramps by determining elevations at the top and bottom of the ramp at the midpoint of the width of each ramp run and calculate the slope using the horizontal ramp length...
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
5.9.2.2 Standing Supports on Dual Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
Platforms with Wheelchair Spaces Recommendations The Committee recommends standing supports located on one side of the platform, integrated into the platform and stretching the full length...
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
EZ-ACCESS® Incline Calculator for Ramp Solutions
EZ-ACCESS® Incline Calculator [Click here to access the online calculator] To Establish the Proper Ramp Length: Determine the incline that your chair is designed to climb...
-
Bicycle Trailers
Trailers add to the total vehicle length and weight, which may decrease speed and maneuverability, while increasing turning radius and stopping distance....
-
10 - foot straightedge method
When used as a specification or requirement, a maximum deviation in length under the straightedge is given, such as "no point shall exceed 1/4 inch under a 10 - foot straightedge."...
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
B. Speaking, Listening, Reading, and Writing: When Auxiliary Aids and Services Must be Provided
The type of aid or service necessary depends on the length and complexity of the communication as well as the format....
-
§ 37.131(c) Fares
., without regard to discounts) for a trip of similar length, at a similar time of day, on the entity's fixed route system....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
4.17.6 Grab Bars
Grab bars complying with the length and positioning shown in Fig. 30(a), (b), (c), and (d) shall be provided....
-
4.17.6 GRAB BARS
Grab bars complying with the length and positioning shown in Fig. 30(a), (b), (c), and (d) shall be provided....
-
Extremely well done!
This video clearly demonstrates the length and dimension of what is expected but often misunderstood by contractors and architects....
