Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
Search Results "Measuring Technique"
-
11B-604.3.1 Size
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
§1607.16 Definitions.
Demonstrated by data showing that the selection procedure measures the degree to which candidates have identifiable characteristics which have been determined to be important for successful...
-
4.5 Maneuvering Clearances
The differences between the UDI findings and the other studies suggest great differences in their protocol or measurement technique....
-
Stabila, Inc. Tech Digital Electronic Level Type 196-2
Electronic measuring technology / Two digital displays / Audible inclination guide / IP 65 Dust and Waterproof / Removable shock-absorbing end caps with anti-slip wall grips....
-
Redi Free® with Redi Base® Shower Pans
How to Measure Depth is measured from the front of curb/entrance to the outside of the back splash wall....
-
Redi Free® with Redi Trench® Shower Pans
How to Measure Depth is measured from the front of curb/entrance to the outside of the back splash wall....
-
Sec.36.304(d)(1)
1) Except as provided in paragraph (d)(2) of this section, measures taken to comply with the barrier removal requirements of this section shall comply with the applicable requirements for...
-
Abstract
ABSTRACT This pilot study conducted human subject testing and objective measures of firmness and stability on nine types of exterior surfaces as part of Phase II of the Accessible Exterior...
-
TEST NO. 1 – INDIVIDUAL BUILDING TEST
The slopes of the undisturbed site measured between the planned entrance and all vehicular or pedestrian arrival points within 50 feet (15 240 mm) of the planned entrance exceed 15 percent...
-
D. Election Day Compliance Review
In the materials provided to each in-precinct Election Coordinator, the Board will include a checklist of the temporary measures to be implemented during the voting period at each...
-
TEST NO. 1 – INDIVIDUAL BUILDING TEST
The slopes of the undisturbed site measured between the planned entrance and all vehicular or pedestrian arrival points within 50 feet (15 240 mm) of the planned entrance exceed 15 percent...
-
11B-233.3.1.2.6.2 Test number one, individual building test
The slopes of the undisturbed site measured in a straight line between the planned entrance and all vehicular or pedestrian arrival points within 50 feet (15,240 mm) of the planned entrance...
-
TEST NO. 1 – INDIVIDUAL BUILDING TEST
It is not required by this code to provide an accessible route when the terrain of the site is such that both of the following apply: The slopes of the undisturbed site measured between...
-
1 [§ 4.7.3]
1 [§ 4.7.3] Only measure the width of the ramp section of the curb ramp (labeled “ramp” to the right [below]). The ramp section of a curb ramp is also known as the “ramp run.”...
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
Door Pressure Gauge
Door Pressure Gauge This Door Pressure Gauge, available from Evan Terry Associates, measures forces from 0-35 pounds on one side and 0-16 kilograms on the other....
-
Digital inclinometers (SmartTool®)
Digital inclinometers (SmartTool®), while slightly more expensive than standard levels, are easy to calibrate and use and can measure slopes in degrees, percent, and fractions per foot....
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
Radiologic Equipment
In these cases, use of a patient lift or another transfer and positioning technique is particularly important for access to this equipment....
-
Purpose of the project
Purpose of the project Accessibility standards reference industry guidance in the measure of field and construction tolerances....
-
Lavatories Adjacent to Partitions
Recently, an interpretation has been presented in how the 18” measurement is applied to the lavatory. ...
