Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
Search Results "Measuring Technique"
-
703.4.1 Height above Finish Floor or Ground
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
M301.4.2 Clearance Around Base
The base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
12112(b)(7)
impairs sensory, manual, or speaking skills, such test results accurately reflect the skills, aptitude, or whatever other factor of such applicant or employee that such test purports to measure...
-
D. Tools Needed
Tools Needed The following items are needed for the survey: A metal tape measure that is at least 20 feet long; A digital level or bubble level that is 24 inches long...
-
§104.13(b)
that impairs sensory, manual, or speaking skills, the test results accurately reflect the applicant's or employee's job skills, aptitude, or whatever other factor the test purports to measure...
-
12112(b)(7)
impairs sensory, manual, or speaking skills, such test results accurately reflect the skills, aptitude, or whatever other factor of such applicant or employee that such test purports to measure...
-
Verify Electrical
Measure to top or bottom of boxes 11B-308.1.1 Heights of all electrical switch boxes....
-
R103 Conventions (Section-by-Section Analysis)
Measurements are stated in metric and U.S. customary units, and each system of measurement is to be used independently of the other....
-
Verify Electrical
Measure to top or bottom of boxes 11B-308.1.1 Heights of all electrical switch boxes....
-
1.2.6
1.2.6 When local variations (flatness) in running slope of ramps are measured according to 1.1.13 at least 80% (rounded to the nearest whole number) of the measurements should not exceed...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059...
-
604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1525 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1420 mm) deep minimum for wall hung water closets and...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets and...
-
D. Election Day Compliance Review
In the materials provided to each Election Judge for Election Day, the County will include a checklist of the temporary measures to be implemented on Election Day at each...
-
604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1525 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1420 mm) deep minimum for wall hung water closets and...
-
604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1525 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1420 mm) deep minimum for wall hung water closets and...
-
D. Election Day Compliance Review
In the materials provided to each Judge of Election for Election Day, the County will include a checklist of the temporary measures to be implemented on Election Day at each polling...
-
2.2.5 Grip Strength
2.2.5 Grip Strength Four types of grip strength measurements for the dominant hand were assessed....
-
What surface characteristics are required of an accessible route?
No standards or methods of measurement are specified in scoping or technical provisions, although the Appendix to ADAAG contains advisory recommendations for slip resistance values derived...
-
Transfer Surface Height (M301.2.1 and M302.2.1)
M301.2.1 and M302.2.1 would require the height of the transfer surface during patient transfer to be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer...
-
Parent Asks for an Evaluation of the Student
These measures (for example, self-management techniques or medication) are often referred to as mitigating measures....
-
Introduction
Data collection included 3 dimensional measurements of approximately 90 points located on the body and device....