Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
Search Results "Measuring Technique"
-
604.3.1 Size
-
1.2.1 Walks and other non - ramp surfaces
When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
§ 37.151(a)(2)
(2) The entity determines that it cannot make measured progress toward compliance in any year before full compliance is required....
-
Background
Further, industry standards, specifications, and measurement procedures do not even address some measures important to facility usability in new construction, such as how to measure the...
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. ...
-
Definitions
that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is achieved through permanent architectural measures...
-
EXHIBIT 1 JEFFERSON OUTPATIENT IMAGING ADA POLICY AND PROCEDURE
Jefferson Outpatient staff have been and will continue to be trained in proper transfer techniques, and will use staff, adjustable equipment (where available), or patient lifts, when appropriate...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
Stabila, Inc. Magnetic Tech Digital Electronic Level Type 96M-2
Electronic measuring technology / Two digital displays / Audible inclination guide / IP 65 Dust and Waterproof / Rare earth magnets for hands free use / Removable shock-absorbing end caps...
-
Rollability and Smoothness of Walking Surfaces
There are smoothness measures for road surfaces but no similar measures for walking surfaces....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
10 - foot straightedge method
However, there is no standardized protocol to measure deviations in lengths less than ten feet. The same problem exists when measuring slope....
-
Documentation of Impact and Validity Evidence
(5) Criterion measures. ...
-
§1607.15 Documentation of impact and validity evidence.
(5) Criterion measures. ...
-
VII. Existing Facilities: Removal of Barriers
Examples of barrier removal measures include -- Installing ramps, Making curb cuts at sidewalks and entrances, Rearranging tables, chairs, vending machines, display...
-
1(2)(a)(i) Individual building test
It is impractical to provide an accessible entrance served by an accessible route when the terrain of the site is such that: (A) the slopes of the undisturbed site measured between the...
-
E. Staff Training
Subject Matter Experts and/or an outside source to all employees in the Elections Division and any relevant contractors or vendors, including those who conduct surveys or implement temporary measures...
-
§382.21(c)
(c) If a passenger with a communicable disease meeting the direct threat criteria of this section gives you a medical certificate of the kind outlined in §382.23(c)(2) describing measures...
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
4.34.6.4(1)
(1) The counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable or replaceable as...
