(3) Third, a public accommodation should take measures to provide access to restroom facilities....
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
Sec.36.304(c)(3)
-
§ 36.304(c)(3)
(3) Third, a public accommodation should take measures to provide access to restroom facilities....
-
Documentation of Impact and Validity Evidence
(5) Criterion measures. ...
-
§1607.15 Documentation of impact and validity evidence.
(5) Criterion measures. ...
-
Background
Further, industry standards, specifications, and measurement procedures do not even address some measures important to facility usability in new construction, such as how to measure the...
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
1.2.1 Walks and other non - ramp surfaces
When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
§ 37.151(a)(2)
(2) The entity determines that it cannot make measured progress toward compliance in any year before full compliance is required....
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. ...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
Definitions
that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is achieved through permanent architectural measures...
-
EXHIBIT 1 JEFFERSON OUTPATIENT IMAGING ADA POLICY AND PROCEDURE
Jefferson Outpatient staff have been and will continue to be trained in proper transfer techniques, and will use staff, adjustable equipment (where available), or patient lifts, when appropriate...
-
Stabila, Inc. Magnetic Tech Digital Electronic Level Type 96M-2
Electronic measuring technology / Two digital displays / Audible inclination guide / IP 65 Dust and Waterproof / Rare earth magnets for hands free use / Removable shock-absorbing end caps...
-
Rollability and Smoothness of Walking Surfaces
There are smoothness measures for road surfaces but no similar measures for walking surfaces....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
10 - foot straightedge method
However, there is no standardized protocol to measure deviations in lengths less than ten feet. The same problem exists when measuring slope....
-
Effect on Removal of Barriers in Existing Facilities: ADA Standard Section 101.2
Section 101.2 of the ADA Standards covers the effects of the removal of barriers in existing facilities.
-
4.5 Maneuvering Clearances
The differences between the UDI findings and the other studies suggest great differences in their protocol or measurement technique....
-
§1607.16 Definitions.
Demonstrated by data showing that the selection procedure measures the degree to which candidates have identifiable characteristics which have been determined to be important for successful...
-
VII. Existing Facilities: Removal of Barriers
Examples of barrier removal measures include -- Installing ramps, Making curb cuts at sidewalks and entrances, Rearranging tables, chairs, vending machines, display...
-
1(2)(a)(i) Individual building test
It is impractical to provide an accessible entrance served by an accessible route when the terrain of the site is such that: (A) the slopes of the undisturbed site measured between the...
-
E. Staff Training
Subject Matter Experts and/or an outside source to all employees in the Elections Division and any relevant contractors or vendors, including those who conduct surveys or implement temporary measures...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
