Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
Search Results "Minimum Dimension"
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
11B-233.3.1.2.6.1 Single building with one common (lobby) entrance
Sites where either Test No. 1 or Test No. 3 is used and it is determined that an accessible route to the common (lobby) entrance is not required, a minimum of 20 percent of the ground floor...
-
11B-809.12 Electrical receptacles, controls and switches
controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured from the top of the receptacle box and 15 inches (381 mm) minimum...
-
11B-809.12 Electrical receptacles, controls and switches
controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured from the top of the receptacle box and 15 inches (381 mm) minimum...
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
11B-406.5.12 Detectable warnings
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
-
11B-405.9.2 Curb or barrier
A curb, 2 inches (51 mm) high minimum, or barrier shall be provided that prevents the passage of a 4 inch (102 mm) diameter sphere, where any portion of the sphere is within 4 inches (102...
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
(Significant Changes – Edge Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection...
-
904.4 Sales and Service Counters
the number of existing counters at work stations or a reduction of the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum...
-
Elevated Play Components
Play areas with 20 or more elevated components must use ramps to connect a minimum of 25 percent of those components. ...
-
224.4 Guest Rooms with Communication Features
Table 224.4 Guest Rooms with Communication Features Total Number of Guest Rooms Provided Minimum Number of Required Guest Rooms With Communication Features...
-
F224.4 Guest Rooms with Communication Features
Table 224.4 Guest Rooms with Communication Features Total Number of Guest Rooms Provided Minimum Number of Required Guest Rooms With Communication Features...
-
606.3 Height
In residential dwelling unit kitchens, sinks that are adjustable to variable heights, 29 inches (735 mm) minimum and 36 inches (915 mm) maximum, shall be permitted where rough-in plumbing...
-
303.3 Beveled
Changes in level between 1/4 inch (6.4 mm) high minimum and 1/2 inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
-
5.2.1.3 Transfer Surface Size Recommendations for Stretchers (M301)
5.2.1.3 Transfer Surface Size Recommendations for Stretchers (M301) The Committee recommends a minimum transfer surface size of 28 inches wide by 17 inches deep for stretchers located...
-
Openings [1016.6]
Where possible, drainage grates should be located outside the minimum clear width of the ORAR....
-
Tent Pads and Tent Platforms [1013]
No minimum tent pad size is specified because the types of tents commonly used in camping facilities can vary depending on the setting....
-
406.4 Landings
The landing clear length shall be 36 inches (915 mm) minimum. The landing clear width shall be at least as wide as the curb ramp, excluding flared sides, leading to the landing....
-
Some wheelchairs weigh more than 600 pounds when occupied, and the design load of the lifts on our vehicles is 800 pounds. Is a transportation operator required to carry these “overweight” wheelchairs?
If a lift has the minimum design load of 600 pounds, there is no requirement for an agency to transport a heavier occupied device....
-
MAKING THE BUILT ENVIRONMENT ACCESSIBLE
____________________________________________________________________________ The ADA's regulations and the ADA Standards for Accessible Design, originally published in 1991, set the minimum...
-
904.4 Sales and Service Counters
the number of existing counters at work stations or a reduction of the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum...
-
405.9 Edge Protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area...
-
Companion Seating
However, the minimum number of wheelchair spaces plus their companion seats still must be provided....