And I know you’re talking about how you do your follow-up studies and all that afterwards to find out how the building actually works....
Search Results "Work Surface"
-
Pricilla Rogers, Ph.D. Making the “Invisible” World “Visible”
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
- Lutron Caséta Wireless Dimmers and Switches
-
Online Guide Project Team
He has 20-plus years' experience using and working with Assistive Technology....
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate FS 33538 of Federal Standard 595C....
-
RAMP
A walking surface in an accessible space that has a running slope greater than 1:20....
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate 33538 of SAE AMS-STD-595A....
-
Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
Executive summary
Results showed a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb. ...
-
5.7.1 Lift Compatibility Clearance in Base for M301
effective, they must deploy at diagnostic equipment such that the boom of the lifts can maneuver far enough over the equipment to safely lower and raise the patient onto and off examination surfaces...
-
"Service Animal'' (Section-by-Section Analysis)
(Section-by-Section Analysis) Section 36.104 of the 1991 title III regulation defines a ‘‘service animal'' as ‘‘any guide dog, signal dog, or other animal individually trained to do work...
-
¾ Inch Minus and ¼ Inch Minus Limestone
The surface stayed soft under foot, enough to see footprints compacted and not return to the surface, but did not show any signs of erosion....
-
Soiltac Liquid Topical
The first noticeable signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....