[DSA-AC] The line where two surface planes with different slopes meet....
Search Results "Work Surface"
-
GRADE BREAK
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
106.5.76 Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
Documentation of Impact and Validity Evidence
Where a job analysis is required a complete description of the work behavior(s) or work outcome(s), and measures of their criticality or importance should be provided (Essential)....
-
§1607.15 Documentation of impact and validity evidence.
Where a job analysis is required a complete description of the work behavior(s) or work outcome(s), and measures of their criticality or importance should be provided (Essential)....
-
Problem Three (Entrance)
Problem Three: The entrance doors are narrow double leaf doors that are normally opened by an automatic door opener but it is not working on Election Day....
-
Define "task." (Section-by-Section Analysis)
However, the Department has proposed additional examples of work or tasks to help illustrate this requirement in the definition....
-
The Accessibility Resource Center
training information and contact details for the Center can be found at: The Section 508 ARC Intranet page: http://ssahost.ba.ssa.gov/arc/ Please note that the above link does not work...
-
The Rehabilitation Act
Commuting to work, c. 1970. — Kaiser Permanente Historical Archives...
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
Pricilla Rogers, Ph.D. Making the “Invisible” World “Visible”
And I know you’re talking about how you do your follow-up studies and all that afterwards to find out how the building actually works....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...