., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section and sufficient clearances to permit at least two wheelchair or mobility aid users to reach areas...
Search Results "Hinge Side Clearance"
-
§ 38.83(a)(1) General
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
403 Walking Surfaces
The requirements for walking surfaces derive from existing specifications for accessible routes covering floor or ground surfaces, slope, changes in level, and clearances....
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
11B-410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
Clear Width: ADA Standard Section 404.2.3
Section 404.2.3 covers the current ADA Standards for clear width at manual doors, doorways and manual gates that are part of an accessible route.
-
11B-809.10.6.1 Size
11B-809.10.6.1 or; A shower stall 36 inches (914 mm) deep by 60 inches (1524 mm) wide minimum with an entrance 36 inches (914 mm) minimum when a wall is installed on the opening side...
-
11B-404.2.3 Clear width
Exceptions: In alterations, a projection of 5/8 inch (15.9 mm) maximum into the required clear width shall be permitted for the latch side stop....
-
11B-404.2.3 Clear width
Exceptions: In alterations, a projection of 5/8 inch (15.9 mm) maximum into the required clear width shall be permitted for the latch side stop....
-
Activar Hiawatha 535/509/536/537 Solid 1 inch Diameter Pulls
Material: Aluminum, Brass, Bronze, Stainless Steel CTC: 8", 9", 10", 12" Overall: 9", 10", 11", 13" Projection: 3" Clearance: 2". Optional 2-1/2" clearance upon request....
-
Guardian Barrier-Free WideArea™ Eye/Face Wash GBF1724
Profile of unit is “flattened” to comply with maximum height and knee clearance requirements....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
PULL: CTC: 8" Projection: 3" Clearance: 2" PUSH: Projection: 2-1/2" Clearance: 1-1/2" WEIGHT: 11.5 lbs....
-
Salsbury Industries Designer Wood Locker Single Tier 3 Wide
or 3 wide units 1 wide units come fully assembled while 3 wide units require minor assembly All locker doors are 12" wide x 3/4" deep All locker doors include heavy duty concealed hinges...
-
Salsbury Industries Designer Wood Locker Single Tier 1 Wide
or 3 wide units 1 wide units come fully assembled while 3 wide units require minor assembly All locker doors are 12" wide x 3/4" deep All locker doors include heavy duty concealed hinges...
-
11B-610.3.1 Rectangular seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. FIGURE 11B-610.3.1 RECTANGULAR SHOWER SEAT...
-
608.3.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
610.3.1 Rectangular Seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. Figure 610.3.1 Rectangular Shower Seat...
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
-
802.1.3 Depth
Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum....
-
608.5.1 Transfer Type Shower Compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm...
-
4.7.7 Water Spouts
Water spouts shall be located in the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum from the rear center of the long side of the clear floor or...
-
Is color contrast required for stair nosings?
The ASME A17.1 code requires escalator steps to be demarcated by yellow lines 2” wide maximum along the back and sides....
-
11B-608.3.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
