Hinge: Full length, stainless steel piano type hinge. Lock: Pin tumbler commercial quality, keyed like all other AJW cabinets....
Search Results "Hinge Side Clearance"
-
AJW Architectural Products U8504 Unidoor Seat Cover Dispenser - Recessed
-
11B-904.3.2 Counter
The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
-
T402.7 Edge Guards
Ramps and bridgeplates shall provide edge guards continuously along each side of the ramp or bridgeplate to within 3 inches (75 mm) of the end of the ramp or bridgeplate that is deployed...
-
G. Compartment Size
.: diagonal or side approaches)? [ADA Stds. 4.17.3] Yes __ No __ N/A __ Comments: ___________________________________________...
-
R207.1 General
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
11B-226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances. ◼...
-
Telescopes and Periscopes
Provide knee and toe clearance complying with ABAAS, section 306, under the telescope or periscope (figure 98)....
-
1132A.2 Interior doors and secondary exterior doors
The provisions of this section shall apply to the dwelling unit side of doors leading from the interior of the dwelling unit to an unfinished basement or an attached garage....
-
802.1.3 Depth
Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum....
-
Common Problems with Routes to Building Entrances
Ø Ramps are too steep or go too long without level rest areas; handrails are not provided on both sides....
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces
Standing supports should be located on both sides of platforms, a minimum of 34 inches between supports, integrated into the platform, and 32 inches minimum length (at least 80% of the platform...
-
Approach
One side of the wheelchair space must adjoin an accessible route. The turning space may overlap the accessible route and the required clear floor space....
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
1015.2 Clear Ground Space
clear ground space 36 inches minimum by 48 inches minimum positioned for either a forward or parallel approach to be provided at each distinct viewing location, and one full unobstructed side...
-
§ 38.107(a)(5)
Doorways on the side wall shall have a minimum clear opening width of 39 inches....
-
11B-812.9 Surface marking
The centerline of the text shall be a maximum of 6 inches (152 mm) from the centerline of the vehicle space and its lower corner at, or lower side aligned with, the end of the parking space...
-
§ 38.123(a)(5)
Doorways on the side wall shall have a minimum clear opening width of 39 inches....
-
11B-610.3.1 Rectangular seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall....
-
11B-812.9 Surface marking
The centerline of the text shall be a maximum of 6 inches (152 mm) from the centerline of the vehicle space and its lower corner at, or lower side aligned with, the end of the vehicle space...
-
904.3.2 Counter
The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
-
610.3.1 Rectangular Seats
The side edge of the seat shall be 1 1/2 inches (38 mm) maximum from the adjacent wall....
-
604.9.5 Flush Controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2....
-
Protruding Objects
One element of a barrier-free meeting space for participants who are blind or have low vision requires cane-detectable protruding objects and sufficient head clearance....
-
Adaptability
Rooms need to be designed to provide required clear floor space at fixtures, turning space, and door clearance....