Design parameter considerations Research conducted by the National Center for Accessible Media for the Whitney Museum put forward the following design parameters for shopping for appropriate...
Search Results "Designated Aisle Seat (Assembly)"
Commonly Searched Documents
-
Design parameter considerations
-
§382.61(e)
However, if you replace any of an aircraft's aisle seats with newly manufactured seats, the new seats must include movable aisle armrests as required by this section....
-
DESIGNATED, RESPONSIBLE EMPLOYEE {35.107}
DESIGNATED, RESPONSIBLE EMPLOYEE {35.107} Required if 50+ employees Responsibilities: Coordinate efforts Investigate complaints alleging...
-
2010 STANDARDS FOR ACCESSIBLE DESIGN
The 2010 ADA Standards for Accessible Design (2010 Standards) were published in the Federal Register on September 15, 2010, and will become mandatory after 18 months....
-
C201.5 Design, Development, and Fabrication
Manufacturers shall evaluate the accessibility, usability, and interoperability of telecommunications equipment and customer premises equipment during its product design, development, and...
-
1015.3 Height
On stairways and stepped aisles, from the line connecting the leading edges of the tread nosings. On ramps and ramped aisles, from the ramp surface at the guard....
-
Clear floor space at Lav
Terry, You should identify the minimum dimensions of the clear floor space at the Lav.
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.3 Transfer Sides
5.3 Transfer Sides.
-
5.3 Transfer Sides Recommendations
5.3 Transfer Sides Recommendations
-
Tips for Weighing People Using an Accessible Scale
By June Isaacson Kailes, Associate Director Harris Family Center for Disability and Health Policy Western University of Health Sciences, Pomona, California  Update -...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
§ 36.302(f)(6) Hold and release of accessible seating
(6) Hold and release of accessible seating. ...
- Bobrick Accessibility Video -- Design for Turning Radiuses
-
CHAPTER 16 STRUCTURAL DESIGN
ETA Editor's Note This Guide contains only the excerpts from California Building Code Chapter 16 that are adopted by Division of the State Architect - Access Compliance...
-
CHAPTER 16A STRUCTURAL DESIGN
ETA Editor's Note This Guide contains only the excerpts from California Building Code Chapter 16A that are adopted by Division of the State Architect - Access Compliance...