Seating, tables, or work surfaces 4.30 If provided in accessible spaces, at least one of each type provided....
Search Results "Designated Aisle Seat (Assembly)"
Commonly Searched Documents
-
12. Seating, tables, or work surfaces
- Pilot Rock UT and UTH Series End Accessible Picnic Table Using Steel Tops Seats
- Pilot Rock XT and XTH Series End Accessible Picnic Table - Using Steel Tops and Seats
-
Check-Out Aisles and Sales and Service Counters
Check-Out Aisles and Sales and Service Counters....
-
219.3 Receivers
shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. 2....
-
221.1.1 Florida Vertical Accessibility
facility governed by this code from the duty to provide vertical accessibility to all levels above and below the occupiable grade level, regardless of whether the ADA Standards for Accessible Design...
- GameTime Adaptive Swing Seat
-
Identification of available accessible seating. (Section-by-Section Analysis)
Section 36.302(f)(3) of the proposed rule requires a facility to identify available accessible seating. ...
-
Links
http://www.beneficialdesigns.com/ Built Environment Image Guide http://www.fs.fed.us/recreation/programs/beig/ Designing Sidewalks and Trails for Access Part 1, Review...
-
1.1 Best practices for design
1.1 Best practices for design...
- Storefront Improvement Program (SIP) - City of Cambridge, Massachusetts
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
Lavatory and Accessory Layout by Terry Salo, Architect, CASp
Lavatory and Accessory Layout by Terry Salo, Architect, CASp NOTE: The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper...
-
Guidelines for Requirement 2
fountains and water coolers; toilet rooms and bathing facilities, including water closets, toilet rooms and stalls, urinals, lavatories and mirrors, bathtubs, shower stalls, and sinks; seating...
-
F219.3 Receivers
shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. 2. ...
-
11B-219.3 Receivers
shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. 2. ...
-
11B-219.3 Receivers
shall be permitted to be calculated according to the total number of seats in the assembly areas in the building provided that all receivers are usable with all systems. 2. ...
-
C. Designation of Accessible Vehicles
Designation of Accessible Vehicles. The International Symbol of Accessibility should be displayed as shown in Figure 6....
-
California Water Closet Accessories
Design guidance for locating water closet accessories in single user toilet rooms and best practice placement of the lavatory in new construction giving the owner more options to maintain...
-
APPENDIX E - SEATING PLANS FOR MODIFIED THEATERS
APPENDIX E SEATING PLANS FOR MODIFIED THEATERS...