1.1 Best practices for design...
Search Results "Seat Designation"
Filters
Commonly Searched Documents
-
1.1 Best practices for design
-
Storefront Improvement Program (SIP) - City of Cambridge, Massachusetts
restoration of historic features. 50% matching grant up to $2,500 for signage, lighting and awning improvements Please note that improvements made prior to approval of a design...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS NUMBER OF SEATS MINIMUM NUMBER OF REQUIRED WHEELCHAIR SPACES...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS Number Of Seats Minimum Number Of Required Wheelchair Spaces 4 to 25 1...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS NUMBER OF SEATS MINIMUM NUMBER OF REQUIRED WHEELCHAIR SPACES...
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
Lavatory and Accessory Layout by Terry Salo, Architect, CASp
Lavatory and Accessory Layout by Terry Salo, Architect, CASp NOTE: The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper...
-
§ 36.302(f)(4) Notification of accessible seating locations
(4) Notification of accessible seating locations. ...
-
C. Designation of Accessible Vehicles
Designation of Accessible Vehicles. The International Symbol of Accessibility should be displayed as shown in Figure 6....
-
APPENDIX E - SEATING PLANS FOR MODIFIED THEATERS
APPENDIX E SEATING PLANS FOR MODIFIED THEATERS...
-
Design parameter considerations
Design parameter considerations Research conducted by the National Center for Accessible Media for the Whitney Museum put forward the following design parameters for shopping for appropriate...
-
DESIGNATED, RESPONSIBLE EMPLOYEE {35.107}
DESIGNATED, RESPONSIBLE EMPLOYEE {35.107} Required if 50+ employees Responsibilities: Coordinate efforts Investigate complaints alleging...
-
2010 STANDARDS FOR ACCESSIBLE DESIGN
The 2010 ADA Standards for Accessible Design (2010 Standards) were published in the Federal Register on September 15, 2010, and will become mandatory after 18 months....
-
C201.5 Design, Development, and Fabrication
Manufacturers shall evaluate the accessibility, usability, and interoperability of telecommunications equipment and customer premises equipment during its product design, development, and...
-
SciFit PRO1000 - Seated Upper Body Machine
accessibility Bi-directional exercise Iso-Strength safe, accommodating strength program Very low starting resistance with 191 levels of resistance Premium, standard and bariatric seat...
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
