A perfect accessory to our industry-standard lab tables. The ARM (Adjustable Rotating Mechanism) is the perfect solutions for the challenges of universal design. With the adjustable...
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
Diversified Woodcrafts 9010 ARM Lab Table Accessory
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
Running Slope [1017.7.1]
Running slope, also referred to as grade, is the lengthwise slope of a trail, parallel to the direction of travel. Trails or trail segments of any length may be constructed with...
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes.
-
Slope [4.3.7]
Requirements in 4.3, while based on the expectation of level floors, apply equally to exterior sites. Where the running slope of an accessible route exceeds 5% it must be treated as...
-
Changes in Level [4.5.2]
Vertical changes in level up to ¼ inch are permitted without treatment along accessible routes. Changes in level ¼ to ½ inch must be beveled with a slope no greater than 1:2. Changes...
-
Den
Lamps wired to rocker wall switches Levers on all doors throughout the house FSC certified birdseye and quartersawn maple paneling Zoned heating on...
-
3.1.3.3 Cross Slope of Driveways
The cross slope of driveways shall not exceed 1:33 (3 percent). Exception. The cross slope of driveways may be no more than 1:20 (5 percent) where needed to ensure proper...
-
6.7 Slope
The slopes of beach access routes shall comply with 6.7.1 and 6.7.2
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%. In the...
-
M305.1 General
Supports shall comply with M305.
-
M305.1 General (Section-by-Section Analysis)
This is an introductory section.
-
M305.1 General
Supports shall comply with M305, as applicable.
-
1016.8.3 Slope
Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage....
-
Section 4.26.2
• Section 4.26.2 of the 1991 Standards requires handrail gripping surfaces to have a diameter of 1 ¼ inches to 1 ½ inches, or to provide an equivalent gripping surface....
-
1016.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
1016.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
M305.2.2 Length (Section-by-Section Analysis)
The Board restructured the Committee’s recommendations to fit within the end and side transfer supports discussed above....
-
Populas Vox Perfect Corner Workstation
The Vox Perfect Corner boasts a surface area of 6ft x 6ft, provides extra-low and extra-high range of adjustment, sleek design and amazing durability....
-
Bobrick Reversible Folding Shower Seat B-5181
In the interests of safety and the protection of end users, this seat should not be used to support weights exceeding 360lbs (163 kg)....
-
Assumptions
Assumptions Two industry standard specifications are used to determine the safety and accessibility of each surface: ASTM F1292‒99/04 Standard Specification for Impact Attenuation of...
-
T208.1 General
A passenger access route shall consist of a route complying with T208.2 between wheelchair spaces and doorways, walking surfaces complying with T302, and clearances complying with T504....
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
