Unit 12 ¾" W, 6" front to back depth (325 x 150mm); 17" (430mm) min. clearance below mounting surface is required....
Search Results "Clearance in Base"
-
Bobrick TrimLineSeries Countertop Mounted Paper Towel Dispenser B-526
-
Boolee Voting Booth
All side panel fabric is 300 x 300 urethane-coated polyester Design Specifications All weights and measures subject to minor variations Height: 60: Depth: 24” Width: 34" Clearance...
-
4.3.5.1 90-Degree Turn
4.3.5.1 90-Degree Turn This turning clearance is applicable for exterior and interior circulation, aisles in seating areas, ramps and other locations....
-
M101.5 Dimensions (Section-by-Section Analysis)
The MDE NPRM proposed that the MDE Standards be based on adult dimensions and anthropometrics....
-
Technical Memorandum TM 2013-18 Sinks
804.4 Kitchens / Kitchenettes with Sinks If a sink is provided in a space that is subject to compliance with TAS 804 (Kitchen and Kitchenettes), the sink must comply with TAS 606 based...
-
§8.22(c)
percentage or number than that prescribed in paragraph (b) of this section for any area upon request therefor by any affected recipient or by any State or local government or agency thereof based...
-
Patient Toilet Rooms [6.4]
Patient Toilet Rooms [6.4] ADAAG specifications are based on the independent use of toilet and bathing facilities and do not address alternate designs for assisted use....
-
BACKGROUND
This matter is based upon a complaint filed with the United States Department of Justice, in which a Complainant alleged that Genesis discriminated against her on the basis of her disability...
-
Alterations: ADA Standard Section 223.1.1
Section 223.1.1 ADA Standards for alterations to medical care and long-term care facilities.
-
11B-411.2.1.2.3 Accessibility function button
Each dot shall have a base diameter of 0.059 inch (1.5 mm) minimum and 0.063 inch (1.6 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
-
11B-411.2.1.2.3 Accessibility function button
Each dot shall have a base diameter of 0.059 inch (1.5 mm) minimum and 0.063 inch (1.6 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
-
Actions
Etiquette considered appropriate when interacting with people with disabilities is based primarily on respect and courtesy....
-
Acknowledgements
Access Board or are based on illustrations produced by the U.S. Access Board and the U.S. Department of Justice....
-
§100.143(e)
(e) Determination of appropriate corrective action is fact-based. Not every corrective measure listed in paragraph (d) of this section need be taken for each likely violation....
-
Who is a person with a “record of” a disability under part 382?
Therefore, individuals who do not have an actual current impairment that substantially limits a major life activity would still be protected under part 382 based upon a past diagnosis (or...
-
11B-608.2.3 Alternate roll-in type shower compartments
FIGURE 11B-608.2.3 ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE...
-
Post-Mounted Objects [§307.3]
The 12” limit also applies to the clearance between multiple posts (excluding the sloping portions of handrails)....
-
Clear Floor Space [§309.2]
If clear floor space is obstructed on both sides more than half the minimum required depth, a wider clearance (36” min.) is required for maneuvering and sway....
-
Handrails [ADA Standards §504.6, §505]
Handrails [ADA Standards §504.6, §505] Specifications in the ADA Standards for handrail surfaces and clearances facilitate a power grip along the handrail length....
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
§ 38.125(a)(1) General
., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a seating location...
-
407.3.2 Alphabetic Keys
Where provided, individual alphabetic keys shall be arranged in a QWERTY-based keyboard layout and the “F” and “J” keys shall be tactilely distinct from the other keys....
-
Accessibility
Accessibility: When ceramic tile is used as the flooring surface, design professionals should consider the following, based on ANSI A108.01 and A108.02, where accessibility is a primary...
