Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
Search Results "Clearance in Base"
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
-
§104.33(b)(1)(ii)
(ii) are based upon adherence to procedures that satisfy the requirements of §§104.34, 104.35, and 104.36....
-
M101.4 Dimensions
The standards are based on adult dimensions and anthropometrics. Dimensions that are not stated as "maximum" or "minimum" are absolute....
-
M101.4 Dimensions
The standards are based on adult dimensions and anthropometrics. Dimensions that are not stated as “maximum” or “minimum” are absolute....
-
Site Arrival Points: ADA Standard Section 206.2.1
Section 206.2.1 covers the scoping requirements for site arrival points of accessible routes in the most current ADA Standards.
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
"Qualified Reader" (Section-by-Section Analysis)
Based upon the Department's investigation of complaints alleging that some entities have provided ineffective readers, the Department proposes to define "qualified reader" similarly to "...
-
M101.5 Dimensions
The MDE Standards are based on adult dimensions and anthropometrics. Dimensions that are not stated as “maximum” or “minimum” are absolute....
-
12112(c)(2)(C) Determination
.-- For purposes of this paragraph, the determination of whether an employer controls a corporation shall be based on --...
-
Panel 3: Impacts on Vision – Glare, Contrast, Color (Gregory Knoop, AIA, Moderator)
These edited Proceedings are based on notes by JEW and TOS)...
-
Open Discussion (Panel 3)
These edited Proceedings are based on notes by JEW and TOS)...
-
Open Discussion (Panel 2)
These edited Proceedings are based on notes by JEW and TOS)...
-
12112(c)(2)(C) Determination
(C) Determination For purposes of this paragraph, the determination of whether an employer controls a corporation shall be based on...
-
11B-307.4.1 Guy braces
FIGURE 11B-307.4.1 GUY BRACES FIGURE 11B-307.4 VERTICAL CLEARANCE...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
-
4.3.5.2 180-degree turn
4.3.5.2 180-degree turn Currently, the ADA-ABA does not have a specific clearance for this type of turn. The 1525 mm (60 in.) turning space would be used instead....
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Bobrick ConturaSeries Surface-Mounted Seat-Cover Dispenser B-4221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
