The specifications in these standards are based upon adult dimensions and anthropometrics....
Search Results "Clearance in Base"
-
2.2 PROVISIONS FOR ADULTS
-
Inclusion Solutions Offset Door Hinge
These special hinges are designed to swing the door clear of the opening, adding about 2" additional clearance for wheelchairs and walkers....
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Military Installation
A base, camp, post, station, yard, center, homeport facility for any ship, or other activity or operation under the jurisdiction of the Department of Defense, including any leased facility...
-
§ 38.23(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.95(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.125(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.83(b)(1) Design Load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
Operable Part
Hardware-based user controls for activating, deactivating, or adjusting ICT....
-
Operable Part
Hardware-based user controls for activating, deactivating, or adjusting ICT....
-
Don-Jo Mfg., Inc. Pull Plate CFC7015
Number CFC7015 Dimensions 3-1/2" x 15" Ctc 6" Diameter 3/4" Projection 2-1/4" Clearance 1-...
-
1630.2(r) Direct Threat
The determination that an individual poses a direct threat shall be based on an individualized assessment of the individuals present ability to safely perform the essential functions of...
-
R103 Conventions (Section-by-Section Analysis)
Where the required number of accessible facilities or elements is based on ratios or percentages and remainders or fractions result, the next greater whole number is required....
-
§1630.2(r) Direct Threat
The determination that an individual poses a “direct threat” shall be based on an individualized assessment of the individual's present ability to safely perform the essential functions...
-
§ 38.159(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 37.105(h)
(h) Restrictions priorities based on trip purpose (if the system is demand responsive)....
-
Technical Memorandum TM 2013-23 Storage (Not in Kitchens or Kitchenettes)
.* Based on Advisory 225.2 and input from the U.S....
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
Forward Approach
Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
-
§104.33(b)(1)(ii)
(ii) are based upon adherence to procedures that satisfy the requirements of §§104.34, 104.35, and 104.36....
-
M101.4 Dimensions
The standards are based on adult dimensions and anthropometrics. Dimensions that are not stated as "maximum" or "minimum" are absolute....
