102 Dimensions for Adults and Children The technical requirements are based on adult dimensions and anthropometrics....
Search Results "Clearance Around Base"
Filters
Commonly Searched Documents
-
102 Dimensions for Adults and Children
-
102 Dimensions for Adults and Children
102 Dimensions for Adults and Children The technical requirements are based on adult dimensions and anthropometrics....
-
T504.1 General
Passenger access routes shall provide clearances that are sufficient to permit passengers using wheelchairs to move between wheelchair spaces and doorways that provide accessible boarding...
-
Height – M301.2.1 & M302.2.1
Upon consideration of the subcommittee’s final recommendation, the full committee was unable to come to a consensus around any specific low height requirement, nor the “best practice” recommendation...
-
11. Do not use language that perpetuates negative stereotypes about psychiatric disabilities.
Much work needs to be done to break down stigma around psychiatric disabilities....
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Subcommittee Report - Mammography Subcommittee Report - Stretchers Subcommittee Report - Weight Scales IDeA Center Memo – Transfer Surface Dimensions IDeA Center Memo - Mammography Knee Clearance...
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
Fixed Seating and Tables
At least 27 inches of knee clearance must be provided between the floor and the underside of the table....
-
Requirement 6. Reinforced walls for grab bars.
designed and constructed in such a manner that all premises within covered multifamily dwelling units contain reinforcements in bathroom walls to allow later installation of grab bars around...
-
Foot Travel on Trails and Roads With Restrictions
Department of Agriculture has determined that a minimum of 36 inches (915 millimeters) of clear passage must normally be provided around or through the gate, berm, or other restrictive device...
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible. ...
-
2.4.3 Impetus for Manufacturers to Improve MDE Accessibility
Their design processes are centered around delivering high quality medical devices based on advice primarily from medical professionals, although some manufacturers occasionally seek input...
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Wooster Products Anti-Slip Safety Coatings Systems
SAFE-STRIDE OIL BASE Safe-Stride® is a specially formulated anti-slip safety paint, which contains grit to help provide a tough, sure-footed, and safer-traction surface Applied to cleaned...
-
Overview
However, instead of installing and testing new trail plots at selected sites around the country, NCA would actively seek out sites that had stabilizer products already applied and currently...
-
305.7.1 Forward Approach
Figure 305.7.1 Maneuvering Clearance in an Alcove, Forward Approach...
-
305.7.2 Parallel Approach
Figure 305.7.2 Maneuvering Clearance in an Alcove, Parallel Approach...
-
306.3.1 General
Space under an element between 9 inches (230 mm) and 27 inches (685 mm) above the finish floor or ground shall be considered knee clearance and shall comply with 306.3....
-
Truncated Domes
The proposed rule specified that the truncated domes have a diameter of 0.9 inch, measured at the base....
-
Schumacher: Introduction to Schumacher Elevator Company
Elevators are sold around the world. Specialties include custom cabs, engineering team and a friendly staff! Dealer inquiries are welcome!...
-
Hager Companies Round Wrought Door Pull 4
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order. Add prefix ''H'' to number....
-
Hager Companies Round Wrought Door Pull 12
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2'' (64 mm) Clearance available on special order....
-
Hager Companies Round Wrought Door Pull 3
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order. Add prefix ''H'' to number....
