If only one bar is provided, the clearance must be a minimum of 24 inches on each side of the bar....
Search Results "Clearance Around Base"
-
Grab Bars
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
Accessible Surfaces Located In The Use Zone
located within the use zone, accessible ground surfaces must also be impact attenuating and meet ASTM F 1292-04 Standard Specification for Impact Attenuation of Surface Systems Under and Around...
-
Standards Development
Documenting these solutions will help to advance the field and build a base of support for improving mandatory standards....
-
Volume Control Telephones: ADA Standard Section 704.3
Amplifiers on pay phones are located in the base or the handset or are built into the telephone. Most are operated by pressing a button or key....
-
R305.1.1 Dome Size
The truncated domes shall have a base diameter of 23 mm (0.9 in) minimum and 36 mm (1.4 in) maximum, a top diameter of 50 percent of the base diameter minimum and 65 percent of the base...
-
902.2 Clear Floor or Ground Space
Knee and toe clearance complying...
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
1002.5.3 Transfer Entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
1002.5.3 Transfer Entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
AISLE
., that provides clearances in in compliance with this code....
-
304.3.1 Circular Space
The space shall be permitted to include knee and toe clearance complying with 306....
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
Squatty Potty
Squatty Potty wraps perfectly around your existing toilet and easily stores out of the way when not in use. We designed, created, tried and tested and then did it again and again....
-
Populas Infinity Workstation
ANSI HFES requirements and recommendations are based on accepted human factors, ergonomics research and established professional practices....
-
4.2 Applications of Findings in Design and Standards Development
The recommendations in this section, in most cases, are based on accommodating all but 5% of the WhMD sample we studied....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
1630.16(f)(2)
(2) A covered entity may establish, sponsor, observe or administer the terms of a bona fide benefit plan that are based on underwriting risks, classifying risks, or administering such risks...
-
§1630.16(f)(2)
(2) A covered entity may establish, sponsor, observe or administer the terms of a bona fide benefit plan that are based on underwriting risks, classifying risks, or administering such risks...
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
Technical Memorandum TM 2013-14 Dining Surfaces
In addition, dining surfaces must be dispersed based on TAS 226.2; therefore, each type of dining surface must comply with TAS 902....
