whether 6 inches minimum and 19 inches maximum above the transfer surface would be an appropriate height for transfer supports on diagnostic equipment used by patients in a supine, prone, or side-lying...
Search Results "Latch Side Clearance"
-
5.4.3 Transfer Support Height for M301 and M302
-
Side guard protocol
Percentage of subjects that were able to attain a certain height in the side guard protocol Height (in) % Subjects Side guard 10...
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
Brewer Access™ High-Low Exam Table
The Brewer Company leads the industry in innovation through our comprehensive line of power procedure tables, exam tables, seating, lighting, and broad line of durable medical...
-
Guest Rooms
At least on sleeping area shall provide a clear floor space complying with 305 on both sides of a bed....
-
Sides of Curb Ramps [§406.3]
Sides of Curb Ramps [§406.3] Curb ramps can have returned sides, but a top landing is required under all conditions to allow maneuvering to and from the run....
-
604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with 604.3....
-
604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with 604.3....
-
604.3 Clearance
Clearances around water closets and in toilet compartments shall comply with 604.3....
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
4.2.4.2 RELATIONSHIP OF MANEUVERING CLEARANCE TO WHEELCHAIR SPACES
One full unobstructed side of the clear floor or ground space for a wheelchair shall adjoin or overlap an accessible route or adjoin another wheelchair clear floor space....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
M301.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer...
-
11B-1003.3.2 Boarding pier clearances
Advisory 11B-1003.3.2 Boarding pier clearances. These requirements do not establish a minimum length for accessible boarding piers at boat launch ramps....
-
11B-1003.3.2 Boarding pier clearances
Advisory 11B-1003.3.2 Boarding pier clearances. These requirements do not establish a minimum length for accessible boarding piers at boat launch ramps....
-
C. Toilet Rooms:
PSE shall provide at least nine (9) 60-inch wide accessible toilet compartments, located in multi-user toilet rooms, and at least six (6) accessible water closets with 60-inch wide clearance...
-
19 Inch Low Height
Domestic UL and international IEC standards dictate a 2” clearance from the floor to the bottom of the footrest....
-
5.1 Transfer Surface Height Recommendations
The height provision is the same for MDE used by patients in supine, prone, or side-lying positions (M301) and patients in seated positions (M302)....
-
Gamco 1.25 Inch Diameter Straight Grab Bar with Snap Flange - 125S Series - Snap
Description 12" (305mm), 18" (455mm), 24" (610mm), 30" (760mm), 36" (915mm), 48" (1220mm) standard lengths. 125 Series - 1 1/4" (32mm) diameter stainless steel. Tubing -...
