Requires the Premium User plan or above.
(Login or upgrade your account!)
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812 142 Plan
-
Bradley Grab Bars 1 1/4" with Concealed Mounting 832 142 Plan
Requires the Premium User plan or above. (Login or upgrade your account!) -
Bradley Grab Bars 1 1/4" with Concealed Mounting 832 142 Front Elevation
Requires the Premium User plan or above. (Login or upgrade your account!) -
Side Partitions and Wing Walls
Side partitions or panels and wing walls can also be used to make protruding objects compliant. The bottom edge of panels or partitions must be 27” high maximum....
-
11B-604.8.1.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch....
-
11B-604.8.1.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch. ...
-
Can doors swing into required clear floor or ground space?
into required clear floor or ground spaces in these specific instances: clear floor space at controls for automatic and power assisted doors and gates (404.3.5) fixture clearances...
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
Curb Ramp Requirements [§406]
Curb Ramp Requirements [§406]
-
11B-603.2 Clearances
Clearances shall comply with Section 11B-603.2....
-
11B-603.2 Clearances
Clearances shall comply with Section 11B-603.2....
-
11B-604.9.2 Clearance
Clearance around a water closet shall comply with Section 11B-604.3....
-
11B-604.9.2 Clearance
Clearance around a water closet shall comply with Section 11B-604.3....
-
Knee and Toe Clearance (M303.2.4)
Knee and toe clearance under breast platforms would be 25 inches deep....
-
Southwest Home Products Window Ease Latching System
With Window EaseTM, less than five pounds of force will open, close, and latch virtually any window in seconds....
-
604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
