When the surface of the clear ground space is constructed of asphalt, concrete, or boards, the slope of the clear ground space must be no steeper than 1:48 (2 percent) in any direction....
Search Results "Cross Slope"
Commonly Searched Documents
-
Transfer Access [1014.2.1]
-
13 [§ 4.7.10]
Therefore, if a marked crossing or crosswalk is provided, there must be a 48-inch deep area contained within the markings at the bottom of the ramp to protect people after they descend the...
-
§27.127(e)(2)
evidence do not apply to hearings conducted pursuant to this part, but rules or principles designed to assure production of the most credible evidence available and to subject testimony to cross...
-
Surfaces
could ride a narrow-tired bicycle AND if you could push a chubby 3-year-old child in an "umbrella" stroller across the surface without making ruts, a person in a wheelchair can probably cross...
-
1193.23(b)(4) (Advisory Guidance)
This input should be sought from representatives from a cross-section of disability groups, particularly individuals whose disabilities affect hearing, vision, movement, manipulation, speech...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
Clear Deck Space
Clear Deck Space The base of the transfer platform must have a clear deck space adjacent to it that is 60 by 60 inches minimum, with a slope not steeper than 1:48 so a person using a...
-
Accessible Routes
The accessible route must comply with ADAAG provisions for location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level,...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
11B-1009.5.2 Transfer space
A transfer space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
1012.1 General
parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles (1012.3); and the surface (1012.4) and slope...
-
Trail Study Sites
Layout of the path across the beach was sloped so that the edge of the path would not hold water....
-
Utilities at Recreation Sites
However, if a condition for exception in an alteration project at an existing site prohibits full compliance with a specific requirement for clear floor or ground space (surface, slope,...
- Whitehall Manufacturing Surface Mounted Ligature Resistant Auto-Release Toilet Paper Holder
- Willoughby Industries ASHS-1013-06-15-HCFA Ligature-Resistant Front Access 15" wide Lavatory
- Precision Safe Sidewalks LLC Sidewalk Trip Hazard Repair Service
- Proline Drain
-
2.1
Entry of this Consent Order brings certainty regarding Cinemark's obligation concerning the placement and location of wheelchair spaces, and the depth of the cross-aisles, at all of Cinemark's...
-
Launch Ramps Without Boarding Piers
The portion of the accessible route located within the launch ramp is not required to comply with the slope requirements for accessible routes....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
N. Mobility Disability or Mobility Disabilities
Disability" or "Mobility Disabilities" means any impairment or medical condition that limits a person’s ability to walk, ambulate, maneuver around objects, or to ascend or descend steps or slopes...
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
1014.2.2 Roll-in Access
Where roll-in access is provided, this section requires a level or sloped entry route complying with the technical requirements for outdoor recreation access routes in 1016 or trails in...
-
4.5.2 Changes in Level
Changes in level between 1/4 in and 1/2 in (6 mm and 13 mm) shall be beveled with a slope no greater than 1:2 (see Fig. 7(d))....