ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
F105.2.3 ASTM
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
A. Accessible Voting Program
The Board agrees that the following temporary measures will be implemented where necessary to make an otherwise inaccessible polling place temporarily accessible during the voting period...
-
Accessible Routes (Exterior and Interior)
(See Part 2 of this document for tips on taking measurements.)...
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
Curb Ramps at Marked Crossings and Vehicular Lanes
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured...
-
3. Modified Theaters
Therefore, when wheelchair spaces are relocated one or more row[s] farther back from the screen, that movement is measured from the existing seating plan....
-
Contrast
Commenters considered this provision to be of questionable usefulness and difficult to meet absent a recognized method of measuring resiliency or sound-on-cane contact. Response....
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
j) Safety Hazards Policy
Though Kirola complained of steep paths at Alamo Square Park, the probative value of such testimony is undermined by the lack of any objective data (such as actual measurements of those...
-
Transfer Access [1014.2.1]
The camp shelter floor at the entrance or opening must be no higher than 19 inches when measured from the clear ground space....
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
This depth measurement is from the center-point of the front and back of the transfer surface as shown in Figure 5.2.1.1....
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
The cross slope is measured perpendicular to the direction of pedestrian travel....
-
Carpet [4.5.3]
A pile thickness up to ½ inch (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
Bails et al.
Research findings from many of the field tests used pre-established sizes and features to measure barriers and problems....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
§ 38.175(a)
All doorways shall have, when the door is open, at least 2 footcandles of illumination measured on the door threshold....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
M301.4.1 Clearance in Base (Section-by-Section Analysis)
The MDE NPRM proposed a clearance in the base of 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
Visual Acuity
Well, visual acuity is just a measure of the limit of your vision resolution (slide 7). And this is what is called the ETDRS chart (slides 7 and 8)....
-
4.5 Maneuvering Clearances
The differences between the UDI findings and the other studies suggest great differences in their protocol or measurement technique....