The cross slope of curb ramps and blended transitions shall be 1:48 maximum....
Search Results "Vehicle Ramp"
-
11B-406.5.7 Cross slope
-
11B-406.5.7 Cross slope
The cross slope of curb ramps and blended transitions shall be 1:48 maximum....
-
§ 38.95(a)(2) Exception
If level-entry boarding, portable or platform lifts, ramps or bridge plates meeting the applicable requirements of this section are provided on station platforms or other stops required...
-
Detecto FHD Series Stationary Wheelchair Scale
Please consult factory for pit type installations. 28.5 inch (72 cm) long ramp and 15 ft (4.5 m) indicator cable included....
-
11B-406.5.4 Floor or ground surfaces
Floor or ground surfaces of curb ramps and blended transitions shall comply with Section 11B-405.4....
-
11B-406.5.4 Floor or ground surfaces
Floor or ground surfaces of curb ramps and blended transitions shall comply with Section 11B-405.4....
-
11B-406.5.4 Floor or ground surfaces
Floor or ground surfaces of curb ramps and blended transitions shall comply with Section 11B-405.4....
-
Reasonable Modification /Accommodation
Modification /Accommodation In addition to alteration and program accessibility obligations, public entities may have an obligation under title II and Section 504 to undertake curb ramp...
-
T103 Definitions
transportation vehicles....
-
4.8.1* General
Any part of an accessible route with a slope greater than 1:20 shall be considered a ramp and shall comply with 4.8....
-
4.8.1* GENERAL
Any part of an accessible route with a slope greater than 1:20 shall be considered a ramp and shall comply with 4.8....
-
Slope [§405.2] and Cross Slope [§405.3]
Specifying a running slope of 7.5% maximum and a cross slope of 1.5% maximum for exterior ramps will accommodate most irregularities or variances due to construction methods or materials...
-
f-vi
Is there a level landing, at least 60 inches x 60 inches, when a ramp changes direction? [ADA Standards § 4.8.4] Yes No...
-
§ 38.57(b)
(b) Handrails, stanchions, and seats shall allow a route at least 32 inches wide so that at least two wheelchair or mobility aid users can enter the vehicle and position the wheelchairs...
-
8. Boarding Separately From Wheelchair
A wheelchair user's request to board a fixed route or paratransit vehicle separately from his or her device when the occupied weight of the device exceeds the design load of the vehicle...
-
5.8.1.2.3 Double Ramped Entry – Edge Protection on the Platform Sides
5.8.1.2.3 Double Ramped Entry – Edge Protection on the Platform Sides....
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(a) requires vehicles over 22 feet in length to have enough securement locations and devices to secure two wheelchairs, while vehicles 22 feet and under must be able to accommodate...
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(a) requires vehicles over 22 feet in length to have enough securement locations and devices to secure two wheelchairs, while vehicles 22 feet and under must be able to accommodate...
-
Circular Cross Section: ADA Standard Section 505.7.1
Section 505.7.1 covers the current ADA Standards for the circular cross section of handrail gripping surfaces.
-
Gripping Surface: ADA Standard Section 505.6
Section 505.6 covers the current ADA Standards for the handrail gripping surface.
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping surfaces shall not be...
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping surfaces shall not be...
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
