Where the horizontal gap is more than 3 inches and/or the vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor...
Search Results "Vehicle Ramp"
-
§ 37.42(f)
-
T202.1 General
Non-rail vehicles shall provide at least one means of accessible boarding and alighting that serves each designated stop on the fixed route to which the vehicle is assigned....
-
§ 38.23(a) General
All vehicles covered by this subpart shall provide a level-change mechanism or boarding device (e.g., lift or ramp) complying with paragraph (b) or (c) of this section and sufficient clearances...
-
§ 38.23(c) Vehicle ramp
(c) Vehicle ramp—...
-
§ 38.23(c)(1) Design load
Ramps 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches, with a safety factor of at least 3 based...
-
§ 38.23(c)(2) Ramp surface
(2) Ramp surface....
-
§ 38.23(c)(3) Ramp threshold
(3) Ramp threshold. The transition from roadway or sidewalk and the transition from vehicle floor to the ramp may be vertical without edge treatment up to 1/4 inch....
-
§ 38.23(c)(4) Ramp barriers
(4) Ramp barriers. Each side of the ramp shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
§ 38.23(c)(5) Slope
If the height of the vehicle floor from which the ramp is deployed is 3 inches or less above a 6-inch curb, a maximum slope of 1:4 is permitted; if the height of the vehicle floor from which...
-
§ 38.23(c)(6) Attachment
When in use for boarding or alighting, the ramp shall be firmly attached to the vehicle so that it is not subject to displacement when loading or unloading a heavy power mobility aid and...
-
§ 38.23(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps, including portable ramps stowed in the passenger area, do not impinge on a passenger's...
-
§ 38.23(c)(8) Handrails
If provided, handrails shall allow persons with disabilities to grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process,...
-
§ 38.25(b) Contrast
All step edges, thresholds and the boarding edge of ramps or lift platforms shall have a band of color(s) running the full width of the step or edge which contrasts from the step tread and...
-
T205.1 General
Non-rail vehicles shall provide illumination complying with T503 at ramps, bridgeplates, doorways, and boarding and alighting areas....
-
§ 38.83(c) Vehicle ramp or bridge plate
(c) Vehicle ramp or bridge plate—...
-
§ 38.83(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches, with a safety factor...
-
§ 38.83(c)(2) Ramp surface
(2) Ramp surface....
-
§ 38.83(c)(3) Ramp threshold
(3) Ramp threshold....
-
§ 38.83(c)(4) Ramp barriers
(4) Ramp barriers. Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
§ 38.83(c)(5) Slope
If the height of the vehicle floor, under 50% passenger load, from which the ramp is deployed is 3 inches or less above the station platform a maximum slope of 1:4 is permitted; if the height...
-
§ 38.83(c)(6) Attachment
(6) Attachment—
-
§ 38.83(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridges plates stowed in the passenger...
-
§ 38.83(c)(8) Handrails
If provided, handrails shall allow persons with disabilities to grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process,...
-
§ 38.159(c) Vehicle ramp
(c) Vehicle ramp—...