lockers have a compartment size that is 12" wide, 72" high and 12", 15" or 18" deep Available as 1 wide or 3 wide units Each locker compartment features an adjustable hat shelf, 3 single wall...
Search Results "Head End Wall"
-
Salsbury Industries 61000 Series Single Tier 3 Wide Standard Metal Lockers
-
Benches [1011.2]
However, armrests on both ends of a bench could prevent a person using a mobility device from being able to transfer from the device onto the bench....
-
Fishing piers and platforms. (Section-by-Section Analysis)
If gangways (where only one end of route is attached to land) and floating piers (where neither end is attached to land) are involved, a number of exceptions are provided from the general...
-
Fishing piers and platforms. (Section-by-Section Analysis)
If gangways (where only one end of route is attached to land) and floating piers (where neither end is attached to land) are involved, a number of exceptions are provided from the general...
-
408.4.6 Car Controls
Control panels shall be centered on a side wall....
-
704.2.2 Types III, IV and V construction
Projections from walls of Type III, IV or V construction shall be of any approved material....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
4.9.4(3)
(3) The clear space between handrails and wall shall be 1‒1/2 in (38 mm)....
-
4.8.5(3)
(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm)....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
11B-813.2.1 Adult changing table
Adult changing tables shall be fixed to the floor or a wall and shall comply with Section 11B-813.2.1....
-
408.4.6 Car Controls
Control panels shall be centered on a side wall....
-
1. Sloped Surfaces
Rest one end of the level at the highest point of the sloped surface and lift the other end (see below) until the bubble is in the middle of the tube. This is the “level” position....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
Fire Rings, Grills, Fireplaces, and Woodstoves [1011.2, 1011.3, and 1011.5]
All sides of fire rings and grills are generally usable, unless a wall or other structure on a side renders that side unusable....
-
Flush Controls: ADA Standard Section 604.6
Section 604.6 covers the current ADA Standards for water closets flush controls.
-
Podium
., have everyone sit at a head table with a tabletop microphone) or provide the speaker who has a disability with a hand-held or lavaliere microphone to allow her to speak from a position...
-
1009.2 Pool Lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
Accessible Routes
Accessible route requirements in ADAAG address width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level, doors, egress, and areas...
-
1011.7 Outdoor Rinsing Showers
EXCEPTION: Where vandalism is a consideration, a fixed shower head located at 48 inches (1220 mm) above the ground shall be permitted in place of a hand-held shower spray unit....
-
1011.7 Outdoor Rinsing Showers
EXCEPTION: Where vandalism is a consideration, a fixed shower head located at 48 in (1220 mm) above the ground shall be permitted in place of a hand-held shower spray unit....