Sloped entries shall comply with Chapter 4 except as modified in 1009.3.1 through 1009.3.3....
Search Results "Cross Slope"
2010 ADA Definition
Cross Slope: The slope that is perpendicular to the direction of travel (see running slope).
Filters
Commonly Searched Documents
-
Sloped Entries: ADA Standard Section 1009.3.1
-
11B-705.1.2.7 Track crossings
Detectable warnings at track crossings shall be 36 inches (914 mm) in the direction of pedestrian travel and extend the full width of the circulation path....
-
11B-247.1.2.7 Track crossings
Where it is necessary to cross tracks to reach transit boarding platforms, detectable warnings complying with Sections 11B-705.1.1 and 11B-705.1.2.7 shall be provided....
-
Width [4.7.3] and Surface [4.7.4]
The cross-slope of the curb ramp (2% maximum) must be minimized because it makes wheelchair travel difficult by distributing weight and required force to one side and causing front casters...
-
Stabila, Inc. Magnetic Tech Digital Electronic Level Type 96M-2
FEATURES: Precise slope and angle measurements for metal fabricators, commercial carpenters, plumbers, etc......
-
Slope Meters and Levels
Corada has reviewed several models of slope meters and levels to assist accessibility surveyors in measuring slope and level changes....
-
M-D Building Products, Inc. GEN3 SmartTool™ Digital Level
shows orientation for next step with the word “UP” Takes less than 2 minutes Five Instant Angle Conversion Modes Degrees - Machine set-up, pipe bending, saw set-up Percent Slope...
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
Bosch Five-Point Self-Leveling Alignment Laser GPL 5 S
Description The GPL 5S is a five-point laser that levels, plumbs up, plumbs down, and squares. It accurately transfers and aligns level, plumb and 90 degree square points. With...
-
Bosch 3 Point Self Leveling Alignment Laser Level GPL 3 S
Description The GPL3 offers limitless uses, everything from plumbing up floors and ceilings to installing drywall partitions and establishing benchmarks. And because it can be...
-
Sears Brands, LLC Craftsman 24 in. Digital LaserTrac® Level
Description Item # 00948293000P Model # 48293 The Craftsman 24-in. Digital LaserTrac Level Means You Never Miss a Cut The Craftsman 24-in. digital LaserTrac level clearly...
-
M-D Building Products, Inc. GEN2 SmartTool™ Digital Level
Dependable, Accurate, Measures All Angles. Directional beep Guides you to your angle so you don’t have to see the level Beep rate increases as angle is...
-
11B-405.2 Slope
Ramp runs shall have a running slope not steeper than 1:12. Exception: Reserved....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Where to Measure Along the Route
-
Which transition type do users with disabilities prefer?
When a sidewalk slopes more than 2% in the direction of travel and a walk with a maximum 2% cross slope intersects it, which transition segment type provides the safest usability for the...
-
Husky 24" Line Generator Digital Laser Level
The Husky 24 in. Digital Laser Level features a laser diode located in the laser pulling head at the right of the level and can project a reference line along the wall. This level...
-
Resting Intervals on Trails
Design Tip The cross slope requirement depends on what material is used....
-
11B-810.10 Track crossings
Where a circulation path serving boarding platforms crosses tracks, it shall comply with Section 11B-402....
-
Starodub, Inc. Ultra-Light Inertial Profiler (ULIP) for Sidewalks
Sidewalk and sidewalk ramp guidelines address cross slope limits and running slope (grade) limits over a specified run length....
-
Sloped Entries: ADA Standard Section 1009.3
Sloped entries shall comply with 1009.3. Advisory 1009.3 Sloped Entries. Personal wheelchairs and mobility devices may not be appropriate for submerging in water....
-
11B-406.4.1 Slope
Blended transitions shall have a running slope not steeper than 1:20....
-
11B-609.2.2 Non-circular cross section
Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm)...
