no access aisle to allow deployment of a van’s wheelchair lift, steps at a facility’s entrance or within its serving or selling space, aisles too narrow to accommodate mobility devices, counters...
Search Results "Counter Length"
Filters
Commonly Searched Documents
-
MAKING THE BUILT ENVIRONMENT ACCESSIBLE
-
Common Requirements (R304.5) (Section-by-Section Analysis)
A maximum counter slope of 5 percent is specified for the gutter or street at the foot of curb ramp runs, blended transitions, and turning spaces....
-
FIGURE INDEX
Series and Gates in Series Figure 405.7 Ramp Landings Figure 405.9.1 Extended Floor or Ground Surface Edge Protection Figure 405.9.2 Curb or Barrier Edge Protection Figure 406.2 Counter...
-
11B-1003.3.1 Boat slip clearance
Clear pier space shall be permitted to be 36 inches (914 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (914 mm) wide segments are separated...
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The transfer support would extend horizontally the entire depth of the transfer surface and would be 15 inches minimum in length....
-
1003.3.1 Boat Slip Clearance
Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated...
-
Trailhead Signs
People have made it clear that they want information about trails, including length, grade, and so forth, so that they can make their own decisions about which trail is appropriate for the...
-
604.5.2 Rear Wall
The rear grab bar shall be permitted to be 24 inches (610 mm) long minimum, centered on the water closet, where wall space does not permit a length of 36 inches (915 mm) minimum due to the...
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
A positioning support will extend horizontally along the side of the patient scanning/imaging bed/table and be 12 - 16 inches in length and 3 - 6 inches above the transfer surface....
-
7.2.2.1 Determining Impracticability
One or more conditions for an exception exist that result in significant deviations from the technical provisions of section 7.4.1 through 7.4.8 for over 15 percent of the length of the...
-
Parking Spaces [4.6.3]
The length of accessible spaces is not specified. Access aisles must be as long as the parking space....
-
4.21.2 Size and Clearances
guidelines for roll-in shower stalls are based on residential size fixtures (30" x 60" minimum or the space used by a standard residential tub/shower unit) and spaces (30" minimum depth by the length...
-
4.20.2 Floor Space
The amount of clear floor space in front of a bathtub required by ADAAG (30"-48" min depth depending on the direction of travel by the length of the tub including a seat at the head of the...
-
Slope [§405.2] and Cross Slope [§405.3]
Slope [§405.2] and Cross Slope [§405.3] Slope represents the proportion of vertical rise to horizontal length and is specified in the Standards as a ratio (e.g., 1:12)....
-
EFFECTIVE COMMUNICATION DURING FACE-TO-FACE SERVICES
The determination shall take into account the nature, circumstances, length, complexity, and importance of the communication, as well as the communication skills of the person with a disability...
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are less than 1000 square feet (93 m2) and defined by permanently installed partitions, counters, casework, or furnishings...
-
Landscape Forms Inc. Scarborough Bench Collection
., 72in. or 96in. lengths. Backless bench in 48in., 72in. or 96in. lengths. Horizontal strap or woven metal seat....
-
11B-805 Medical care and long-term care facilities
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurses’ stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
Utility Sinks
Ensure that the height of the counter or rim surrounding the utility sink is not more than 34 inches (865 millimeters) above the ground or floor space and that the bottom of the bowl is...
-
Height and Clearances [4.19.2]
The lavatory or counter may be deeper than 19 inches but the portion of the required 30 by 48 inch clear floor space must underlap the lavatory a minimum of 17 inches and is limited to a...
-
Section 37.59 Differences in Accessibility Completion Date Requirements
If there is a common entrance to the station, that commuter rail passengers and Amtrak passengers both use, or a common ticket counter, it would have to be accessible by July 1993....
-
Omnia Industries Inc. Interior Modern Lever Latchset - Stainless Steel No.47
Interior Modern Lever Latchset - Stainless Steel Dimensions: 3" Projection x 5- 1/2 " Length, 11/16" Lever Diameter Finishes: US32D...
-
Lowered section for bar
Can anyone show me where a folding lower section of the bar counter can't be used as long as it meets the other requirements? This is not for designing a new bar....
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
Additionally, a transfer approach at the foot location may not be practical for many people with disabilities who would have to move themselves or be moved across a significant length of...
