The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
Search Results "Horizontal Standing Support"
-
§ 38.83(b)(10) Platform movement
-
§ 38.95(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
§382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
§ 382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
504.3 Prompts
operation that prompts authors to create content that conforms to Level A and Level AA Success Criteria and Conformance Requirements in WCAG 2.0 (incorporated by reference, see 702.10.1) for supported...
-
GRAB BAR
[DSA-AC & HCD 1-AC] A bar for the purpose of being grasped by the hand for support. Advisory Definition of GRAB BAR....
-
GRAB BAR
[DSA-AC & HCD 1-AC] A bar for the purpose of being grasped by the hand for support. Advisory Definition of GRAB BAR....
-
Pilot Rock CN-AMQ Amherst Collection Square Ash Receptacles
Specifications: Model CN-AMQ Ash Receptacle is fabricated with 10 ga. steel vertical and horizontal straps. ...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
R308.1.2.1 Platform and Vehicle Floor Coordination
Department of Transportation regulations (49 CFR parts 37 and 38) require the height of the vehicle floor and the station platform to be coordinated so as to minimize the vertical and horizontal...
-
7(2)(b)(v)
(v) Vanities and lavatories are installed with the centerline of the fixture a minimum of 1'3" horizontally from an adjoining wall or fixture....
-
Cross Slope
This may be expressed as the percentage of change in elevation or as a ratio of vertical distance to horizontal distance....
-
§ 38.93(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d)(1) or (d)(2) of this section, car, platform or portable lifts complying with §38.95...
-
§ 38.95(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier down (if applicable) or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
-
§ 38.125(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
GRAB BAR
[DSA-AC & HCD 1-AC] A bar for the purpose of being grasped by the hand for support. Advisory Definition of GRAB BAR. ...
-
504.4 Templates
conforms to Level A and Level AA Success Criteria and Conformance Requirements in WCAG 2.0 (incorporated by reference, see 702.10.1) shall be provided for a range of template uses for supported...
-
EZ-ACCESS Transitions® Angled Entry Ramp
The Transitions Angled Entry Ramp – is a portable, stand-alone threshold ramp featuring independently adjustable legs with swivel feet, allowing for vertical adjustment ranging from 1-3/...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
