When the lift is at car floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
Search Results "Horizontal Standing Support"
Filters
Commonly Searched Documents
-
§ 38.125(b)(7) Platform gaps
-
Grab bar clearance
Have local authorities accepted one-piece dispensers in toilet compartments that are recessed behind the horizontal grab bars? These units stick out ¼" or so....
-
Best Practice Recommendations for Layout Planning
When possible, include both “horizontal” (side to side) and “vertical” (front to back) aisles to improve access and flow....
-
§382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
§ 382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
Armrests (M302.3.2)
This is consistent with ANSI/AAMI HE75 which recommends that “[f]or support surfaces that require the patient to assume a seated position, armrests should be provided to enhance patient...
-
Don-Jo Mfg., Inc. 2-3/4" Hospital Latch 4500
Shelf pack 1 Features UL Listed, Works with 1-3/4" doors, Lever projection 3-1/4", Non Handed, Push/Pull latch can be mounted with the handles up, down or horizontal...
-
505.10.2 Top Extension at Stairs
At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beginning directly above the first riser nosing....
-
f-v
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided at every 30 feet of horizontal length?...
-
4d.
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
6d. Ramp Length
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
Extensions
Handrails that are not continuous must have horizontal extensions at both the top and bottom of the ramp at least 12 inches long that are rounded or returned smoothly to walls, posts, or...
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
Smith System Flex Single-Student Desk 01368 & 01371
Its design moves the support away from the corners so the student has more knee room for easier ingress/egress, saving time she/he stands up or sits down....
-
GameTime Sounds of Water Panel
Add to a PlayTrails play pocket or use along any trail or pathway as a stand-alone educational sign to maximize the value in your play space....
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
11B-803.6 Mirrors
reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person on the bench as well as to a person in a standing...
-
Lifting Capacity
Lifting Capacity Lifts must have the capability of supporting a minimum weight of 300 pounds and be capable of sustaining a static load that is at least 1.5 times the rated load....
-
Nana Wall Systems, Inc. Sliding Glass Walls With Solid Wood HSW66
The system is a completely top-supported design therefore the number of panels is only limited by the supporting structure in your design. ...
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
