504.3 Prompts (Section-by-Section Analysis) This proposed section would require authoring tools to proactively support the creation of accessible content by providing a mode of operation...
Search Results "Horizontal Standing Support"
Filters
Commonly Searched Documents
-
504.3 Prompts (Section-by-Section Analysis)
-
§ 38.159(c)(1) Design load
Ramps 30 inches (760 mm) or longer shall support a load of 600 pounds (2665 N), placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches (660 mm by 660 mm),...
-
Window Ease
Window Ease™ attaches to any manufactured single-hung, double-hung or horizontal sliding window....
-
Southwest Home Products Window Ease Latching System
Modifies New or Existing Windows For Vertical or Horizontal Sliding Windows Compliance with All Codes Guaranteed Window EaseTM is not a window....
-
12209(a)(1) Commitment to Rule XLII
.-- The Senate reaffirms its commitment to Rule XLII of the Standing Rules of the Senate which provides as follows: No member, officer, or employee of the Senate shall, with respect to...
-
Exceptions [1014.1, Exceptions 1 and 2]
Many times, the roof of a camp shelter is sloped or does not permit someone to stand fully erect while in the shelter....
-
201.3 Temporary and Permanent Structures
Temporary buildings or facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed...
-
4.6.6 Passenger Loading Zones
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....
-
Alterations and Additions
requirements that form the basis for the Department of Justice’s 2010 ADA Standards and the Department of Transportation's ADA Standards and is not intended to be comprehensive or used as a stand-alone...
-
11B-201.3 Temporary and permanent structures
Temporary buildings or facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed...
-
i) Grievance Procedures
Kirola lacks standing to challenge the City's grievance procedure.22 At trial, Kirola testified to having made a single request for the removal of an access barrier; namely, her July 2006...
-
I. INTRODUCTION
Separately, the City filed a Post-Trial Motion for Judgment, focusing primarily on whether Kirola has constitutional standing under Article III to pursue any claims on behalf of herself...
-
Section 37.23 Service Under Contract
The Department also notes that the “stands in the shoes” requirement may differ depending on the kind of service involved....
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane)....
-
4.9.4(2)
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
§ 38.53(d)(1) Requirements
Where new vehicles will operate in new stations, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal gap between each vehicle door at rest...
-
§ 38.173(b)
(b) Where the vehicle covered by paragraph (a) will operate in an accessible station, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal...
-
11B-216.4.1 Exit doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
-
4. Wheelchair seat depth
Wheelchair seat depth For this study, wheelchair seat depth was calculated as the horizontal distance from the proximal (i.e., towards the rear) edge to the distal (i.e., towards the...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
