TIA 1083 defines measurement procedures and performance requirements for the handset generated audio band magnetic noise of wire line telephones, including digital cordless telephones....
Search Results "Mitigating Measures"
-
E102.8 Telecommunications Industry Association (TIA)
-
III-9.8000 Certification and barrier removal in existing facilities
The Department will measure equivalency against subpart D of the title III rule, New Construction and Alterations....
-
Can handrails or other elements overlap door maneuvering clearances?
The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
-
4 - Best practices for construction observation
Even though the final responsibility rests with the contractor, the architect, or other design professional should be observing construction and requiring the contractor to use the measurement...
-
Can handrails overlap door maneuvering clearances?
The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
Accessible Ground Surfaces
This standard assesses the accessibility of a surface by measuring the work an individual must exert to propel a wheelchair across the surface....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Chapter M3 Technical Criteria
The technical criteria specify measurements in inches and millimeters....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
due to unusual characteristics of the site when: The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
11B-809.12 Electrical receptacles, controls and switches
circuits of 30 amperes or less, communication system receptacles, controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured...
-
Appendix Two: Design Information and Accommodation Models
Research findings on Eye Height, measured on the right eye Type of WhMD user Sam-ple Size Mean (SD) Min 5%ile 10%ile Me-dian 90%ile...
-
2.4.1 Current Marketplace Dynamics
Notes I The methods for measuring “low heights” for current height adjustable products vary among manufacturers and product designs. No official measurement method currently exists....
-
Hospital and healthcare settings. (Section-by-Section Analysis)
A direct threat is defined as a significant risk to the health or safety of others that cannot be eliminated or mitigated by a modification of polices, practices, or procedures. ...
-
Base Support [No specific provision—affects M303.2.4]
The footrest height data measures the height from the floor to the top surface of the footrest at its proximal outside corner....
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
The height of water closet seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the floor, measured to the top of the seat....