qualification standard, test or other selection criterion operates to screen out an individual with a disability, or a class of such individuals on the basis of disability, it must be a legitimate measure...
Search Results "Mitigating Measures"
-
1. Job-Related
-
Truncated Domes
The proposed rule specified that the truncated domes have a diameter of 0.9 inch, measured at the base....
-
SUMMARY OF THE 19-INCH RECOMMENDATION
Note that height measurement, as defined by the tables and chairs subcommittee, represents the highest point of the transfer surface, inclusive of bolsters, when measuring to the top of...
-
3.3.3 Clear Floor Width
Neither the DfT or DETR studies collected data on occupied width but did measure the unoccupied device width....
-
1 - Design and drawing
In addition, current practice for architectural and construction engineering drawings establish ambiguity and the potential for accumulated measurement error....
-
Access-Able Designs Portable Clamp-On Tub Seat SH-426
Measures 26.5" W x 15" D. Custom sizes available. 5 year warranty....
-
Bobrick Recessed Toilet Tissue Dispenser B-6677
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
Bobrick Recessed Toilet Tissue Dispenser B-667
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
Access-Able Designs Shower Transfer Bench SH-400-2SDL
Measures 32" W x 15" D x 22.5" D. Complies w/ ADA 4.21.3 when properly installed 5 year warranty....
-
Final Regulatory Flexibility Analysis
B: Initial Regulatory Assessment, sections entitled, ‘‘Regulatory Alternatives,'' ‘‘Regulatory Proposals with Cost Implications,'' and ‘‘Measurement of Incremental Benefits'' (estimating...
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
To facilitate transfers and to mitigate this fall hazard, the Committee proposes the inclusion of transfer supports (M301.3)....
-
1019.1 General
U.S.C. 4332; 40 CFR 1505.2); Agreements executed or decisions issued by a federal agency pursuant to National Historic Preservation Act stating how it will avoid, minimize, or mitigate...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
Cross Slope
Measurements, absent live loads, are to be made from a static condition (i.e., absence of movement that results from wind, waves, etc.)....
-
T505.3 Location of Operable Parts
Operable parts shall be located adjacent to the toe end of the clear space or shall be located no more than 10 inches (255 mm) measured from the centerline of the long dimension of the clear...
-
Treads & Risers
[ADA Stds. 4.9] Yes __ No __ N/A __ Comments: ___________________________________________ ...are all stair treads the same depth (at least 11" deep), measured riser to riser, to prevent...
-
Running Slope
In other words, the slope is the difference in elevation from the beginning to the end of a part of a trail, outdoor recreation access route, or beach access route, measured in the direction...
-
Door Closers [4.13.10]
requires that the sweep period of the closer be adjusted so that from an open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 inches from the latch, measured...
-
§ 38.153(c)(1)
(1) Doors shall have a minimum clear width when open of 30 inches (760 mm), measured from the lowest step to a height of at least 48 inches (1220 mm), from which point they may taper to...
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
The Sweet Spot of Speed: A Gentle Introduction to the Clicking Game
If you’ve never tried a click speed test before, or if you’ve only ever seen them in competitive gaming contexts, let me offer a different way to approach it: not as a measure of worth,...
-
5.1.2 Transfer Surface High Height Recommendations for M301 and M302
5.1.2 Transfer Surface High Height Recommendations for M301 and M302 The Committee recommends an adjustable height range with an upper height measuring at least 25 inches....
-
Summary
The data are based on findings from the Anthropometry of Wheeled Mobility (AWM) Project, and comprises of detailed static measurements collected from 500 users of manual wheelchairs, power...
