For ADA survey and compliance tools that will simplify your field measurement process and plan reviews, the Corada Shop has a growing collection of templates and tools that you can download...
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
Updates and Other Pocket Guides
-
Islands: ADA Standard Section 406.7
Section 406.7 covers the current ADA Standards for islands.
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
5.8.2 Knee and Toe Clearance Recommendations under Breast Platform Recommendations
Rationale for recommendation Each of these measurements creates a more accessible piece of imaging equipment while balancing the physical attributes and operation of the equipment....
-
221.9 Stadium Style Movie Theaters
criteria: (i) It is located within the rear 60% of the seats provided in an auditorium; or (ii) It is located within the area of an auditorium in which the vertical viewing angles (as measured...
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2½ inches (64 mm) minimum measured along the vertical centerline of the element....
-
604.9.6 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
Gaps
However, if compliance with those measurements is not operationally or structurally feasible, operators may use bridge plates, ramps or other devices....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2 1/2 inches (64 mm) minimum measured along the vertical centerline of the element....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign. Advisory 502.6 Identification....
-
B. Analysis
Where potential discrimination has been found, entities have taken necessary corrective measures, such as revising policies and procedures; refining quality assurance processes; and implementing...
-
604.9.6 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
406.8 Detectable Warnings
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured...
-
11B-604.9.6 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
-
A4.13.11 Door Opening Force
Forces for pushing or pulling doors open are measured with a push-pull scale under the following conditions:...
-
A4.13.11 DOOR OPENING FORCE
Forces for pushing or pulling doors open are measured with a push-pull scale under the following conditions:...
-
R304.2.3 Flared Sides
Where a pedestrian circulation path crosses the curb ramp, flared sides shall be sloped 10 percent maximum, measured parallel to the curb line. Advisory R304.2.3 Flared Sides....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
4.13.5 CLEAR WIDTH
Doorways shall have a minimum clear opening of 32 in (815 mm) with the door open 90 degrees, measured between the face of the door and the stop (see Fig. 24(a), (b), (c), and (d))....
-
§ 38.159(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway...
-
11B-604.9.6 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...