Department may conduct an on-site review of any QuikTrip facility, review any QuikTrip records related to actions required by the Consent Decree, and interview any QuikTrip employees or contractors...
Search Results "Assurances from Contractors"
Filters
Commonly Searched Documents
-
VIII. REPORTING, MONITORING, ENFORCEMENT, AND OTHER MISCELLANEOUS PROVISIONS
-
Assessment factors. (Section-by-Section Analysis)
include in its policy the procedure by which claims that the other power-driven mobility device is being used for a mobility disability will be assessed for legitimacy (i.e., a credible assurance...
-
II. COMPLIANCE WITH TITLE III OF THE ADA
provide a copy of the policy to each new Web Content Personnel, contractor responsible for web content, and CSO Personnel for www.hrblock.com; c. ...
-
Executive Summary
This software included quality assurance routines to identify errors in datasets and routines to merge other data sets into the database....
-
L-Shaped Seats: ADA Standard Section 610.3.2
Section 610.3.2 covers the current ADA Standards for L-shaped shower compartment seats.
-
11B-610.3.2 L-shaped seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
EXHIBIT H POLICY OF NONDISCRIMINATION ON THE BASIS OF DISABILITY IN EFFECTIVE WEBSITE COMMUNICATIONS
QuikTrip will ensure that persons with disabilities have an equal opportunity to benefit from the goods, services, privileges, advantages, and accommodations offered by QuikTrip through...
-
11B-104.1.1 Construction and manufacturing tolerances
Information on specific tolerances may be available from industry or trade organizations, code groups and building officials, and published references....
-
11B-104.1.1 Construction and manufacturing tolerances
Information on specific tolerances may be available from industry or trade organizations, code groups and building officials, and published references. Â ...
-
Transfer Device
Equipment designed to facilitate the transfer of a person from a wheelchair or other mobility aid to and from an amusement ride seat....
-
Swinging Doors and Gates: ADA Standard Section 404.2.4.1
Section 404.2.4.1 covers the current ADA Standards for maneuvering clearances at swinging doors and gates.
-
More Steps Toward Access
Certification facilitates voluntary ADA compliance by assuring that certified State and local accessibility requirements meet or exceed ADA requirements....
-
11B-604.5.1 Side wall
The side wall grab bar shall be 42 inches (1067 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1372 mm) minimum from the rear wall with...
-
TRANSFER DEVICE
[DSA-AC] Equipment designed to facilitate the transfer of a person from a wheelchair or other mobility aid to and from an amusement ride seat....
-
11B-503.5 Vertical clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone and from the passenger loading zone to a vehicular exit shall provide...
-
D. Technical standards for construct validity studies
Users choosing to justify use of a selection procedure by this strategy should therefore take particular care to assure that the validity study meets the standards set forth below....
-
11B-208.3.3.2
Attached private garages directly serving a single residential dwelling unit shall provide at least one of the following options: A door leading directly from the residential dwelling...
-
1015.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
-
Figure 404.2.4.1(k) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side with Closer – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(i) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side with Closer – Drawing from the U.S. Access Board
-
B.2.ii. - How should an agency proceed in identifying "applicable" technical provisions in Subparts B, C, and D of the Access Board’s standards to ensure acquired products provide comparable access?
For example, if an agency were to enter into a seat management contract for desktop computing resources, the hardware and software to be provided by the contractor would be required to meet...
-
Maintenance
The playground crews ranged in number from 1‒3 staff, usually with one full-time employee and 2‒3 seasonal staff during the summer months. At least 30 minutes was spent on site. ...
-
Accessibility - Flatness and Lippage
For any application, a tiled floor should comply with the flatness requirements in ANSI A108.02: "no variations exceeding 1/4" in 10 feet from the required plane."...
-
EZ-ACCESS PASSPORT® Residential Vertical Platform Lift
Our ETL Certification Mark also assures continued compliance with the applicable regulatory and safety standards throughout North America....
