Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.12.3.2....
Search Results "Segment Length"
-
407.12.3.2 Obstructed Forward Reach
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
11B-812.7 Access aisle
Access aisles shall be 60 inches (1524 mm) wide minimum and shall extend the full required length of the vehicle spaces they serve....
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
-
Refuge Islands
"(29) However, recumbent bicycles, bicycles with trailers, and hand cycles all have 85th percentile lengths greater than 1.8 m (6 ft)....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
Landings
Must be as wide as the ramp they connect to A minimum length of 60 inches (1525 mm) If ramps change direction, the minimum landing size must be 60 inches (1525 mm) wide...
-
407.12.3.1 Unobstructed Forward Reach
Where the operable part is located at the leading edge of the maximum protrusion within the length of the vertical reference plane of the ICT, the operable part shall be 48 inches (1220...
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
11B-1003.2.1 Boat slips
Exceptions: Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with Section 11B-1003.2...
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1.1.11 Ramp running slope
overall running slope of ramps by determining elevations at the top and bottom of the ramp at the midpoint of the width of each ramp run and calculate the slope using the horizontal ramp length...
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
Do the ACAA and its implementing regulations (14 CFR part 382 or part 382) apply to both U.S. and foreign carriers?
foreign air carriers is Section 382.70(b), which expressly requires foreign carriers to record, categorize, and report written disability-related complaints associated with any flight segment...
-
Designed Use
There is only one "Designed Use" per trail or trail segment....
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
11B-809.2.2 Turning space
However, the overlap of turning space must be limited to one segment of the T-turn so that back-up maneuvering is not restricted....
-
Coverage and Definition of “Flight”
carrier operates a flight between two non-U.S. points and the flight carries the code of a U.S. carrier, the final rule will not extend coverage to the foreign carrier for that flight segment...
-
Resting Intervals on Trails
Provide resting intervals between each trail segment any time the running slope exceeds 1:20 (5 percent) as shown in table 5....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....