Ramps must also have edge protection to stop wheelchairs from falling off the sides, and level landings at the top and bottom of each segment and where the ramp changes direction....
Search Results "Segment Length"
-
1. Typical Issues for Individuals Who Use Wheelchairs, Scooters, or other Mobility Devices
-
Complaint Procedures
[Sec. 382.70(c)] 1 Foreign carriers are covered by this section only with respect to disability-related complaints associated with any flight segment originating or terminating in the...
-
Trail Type
managers to identify trail-specific Design Parameters or technical specifications, management needs, and the cost of managing the trail for particular uses and/or seasons by trail or trail segment...
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(a) requires vehicles over 22 feet in length to have enough securement locations and devices to secure two wheelchairs, while vehicles 22 feet and under must be able to accommodate...
-
What kinds of securement equipment must be provided in buses and vans?
Section 38.23(a) requires vehicles over 22 feet in length to have enough securement locations and devices to secure two wheelchairs, while vehicles 22 feet and under must be able to accommodate...
-
11B-505.2 Where required
At door landings, handrails are not required when the ramp run is less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
-
A4.8.2 Slope and Rise
The ability to manage an incline is related to both its slope and its length....
-
Handrail Clearance and Cross Section [§505.5, §505.7]
Handrail Clearance and Cross Section [§505.5, §505.7] Surface requirements and clearances facilitate a power grip along the length of handrails....
-
Handrails [§504.6, §505]
Handrails [§504.6, §505] Handrails are required on both sides of stairs and must be continuous within the full length of each stair flight....
-
11B-812.7.2 Marking
Access aisle markings may extend beyond the minimum required length....
-
11B-505.2 Where required
At door landings, handrails are not required when the ramp run is less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
-
11B-403.7 Continuous gradient
All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
-
11B-403.7 Continuous gradient
All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
-
11B-505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum....
-
406.4 Landings
The landing clear length shall be 36 inches (915 mm) minimum. The landing clear width shall be at least as wide as the curb ramp, excluding flared sides, leading to the landing....
-
11B-403.7 Continuous gradient
All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
-
R304.2.2 Running Slope
The running slope of the curb ramp shall be 5 percent minimum and 8.3 percent maximum but shall not require the ramp length to exceed 4.5 m (15.0 ft)....
-
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191 Bus boarding and alighting areas shall provide a clear length of 96 inches (2440 mm), measured perpendicular...
-
11B-1007.2 Accessible routes
Ramp landing length specified by Section 11B-405.7.3 shall be permitted to be 48 inches (1219 mm) long minimum....
-
11B-1007.2 Accessible routes
Ramp landing length specified by Section 11B-405.7.3 shall be permitted to be 48 inches (1219 mm) long minimum....
-
11B-407.2.3.1 Floor designation
The outside diameter of the star shall be 2 inches (51 mm) and all points shall be of equal length. Raised characters, including the star, shall be white on a black background....
-
General: ADA Standard Section 205.1
Section 205.1 of the ADA Standards covers information on scoping requirements for operable parts in the most current ADA Standards.