The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
Search Results "Transfer Surface"
Filters
Commonly Searched Documents
-
Floor or Ground Surface: ADA Standard Section 802.1.1
-
6. Minimum (Low) Height Standard for Transfer Surfaces
Minimum (Low) Height Standard for Transfer Surfaces As indicated in Section 5.1.1, the MDE Advisory Committee recommends that equipment with transfer surfaces be height adjustable in...
-
Transfer Height: ADA Standard Section 1002.6.2
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they...
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2....
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2....
-
11B-1009.5.4 Transfer steps
Transfer step height shall be 8 inches (203 mm) maximum....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
Seat width and depth
Seat width and depth: ADA-ABA currently requires a minimum entry point of 24 inches for transfer steps in play (Section 1008.3.1.1) [7] and pool areas (Section 1009.4.5) [7]. ...
-
11B-1008.4.5 Transfer supports
Where play components require transfer to entry points or seats, at least one means of support for transferring shall be provided....
-
Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry
Access Board RE: Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry...
-
5.2.2.2 Transfer Surface Depth
5.2.2.2 Transfer Surface Depth. The transfer surface should be 17 inches deep minimum for equipment used by patients in a seated position....
-
Transfer Devices for Use with Amusement Rides: ADA Standard Section 1002.6
When using a transfer device to access an amusement ride, the least number of transfers and the shortest distance is most usable....
-
5.2.2.1 Transfer Surface Width
5.2.2.1 Transfer Surface Width. The transfer surface should be 21 inches wide minimum for examination chairs and other equipment used by patients in a seated position....
-
M301.2.1 Transfer Surface Height
M301.2.1 Transfer Surface Height Subcommittee Recommendation: The imaging subcommittee decided to not specifically come up with a recommendation for transfer height, rather leaving...
-
M302.2.4 Transfer Sides
Options to transfer from a mobility device shall be provided on two adjoining sides of transfer surfaces. ...
-
M302.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
Tread Surface: ADA Standard Section 504.4
Section 504.4 covers the current ADA Standards for the tread surfaces on stairways.
-
Floor or Ground Surface: ADA Standard Section 404.2.4.4
Section 404.2.4.4 covers the current ADA Standards for floor or ground surfaces at door maneuvering clearances.
-
Amusement Ride Seats Designed for Transfer: ADA Standard Section 1002.5
Ride seats designed for transfer should involve only one transfer....
-
Effect of Handhelds on Transfer Height
Only a few people used the backrests during the transfers....
-
Extended Floor or Ground Surface: ADA Standard Section 405.9.1
Section 405.9.1 covers the current ADA Standards for extended floor or ground surface of the ramp run or landing.
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....