Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location....
Search Results "Vertical Alignment"
-
11B-404.3.5 Controls
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-404.3.5 Controls
Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
Spaces and Elements: ADA Standard Section 206.2.4
Section 206.2.4 covers the scoping requirements in the most current ADA Standards for accessible routes connecting spaces and elements within a building.
-
Wheelchair Spaces
Wheelchair spaces should not overlap required exit widths or circulation paths and should provide for shoulder-to-shoulder alignment with occupants of adjacent seats (an important consideration...
-
Landings [4.8.4]
For example, runs should be aligned along the outside landing edge, as in the case of ramps with a 90 degree turn, so that a wider turn is permitted....
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run....
-
221.9 Stadium Style Movie Theaters
at least one of the following criteria: (i) It is located within the rear 60% of the seats provided in an auditorium; or (ii) It is located within the area of an auditorium in which the vertical...
-
Is there a minimum distance between changes in level?
Such level changes may need to be in close proximity, such as at raised thresholds (otherwise a minimum 48” separation will provide enough wheelchair space so that only one vertical change...
-
1132A.4.1, Item 1
Thresholds with a change in height of not more than ¼ inch (6.35 mm) may be vertical....
-
1132A.4.1, Item 1
Thresholds with a change in height of not more than ¼ inch (6.35 mm) may be vertical....
-
Priority 1: Approach & Entrance
Word Fillable Form (1.5MB) Word Non-Fillable Form (1.3MB) PDF Non-Fillable Form (0.8MB)
-
11B-810.2.3 Connection
shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped at 35 degrees maximum from vertical...
-
11B-810.2.3 Connection
shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped at 35 degrees maximum from vertical...
-
Obstructions [4.7.8]
Space is needed at the top and bottom of ramps so that people using wheelchairs can align with the running slope and maneuver from ramps, including when making turns (which is difficult...
- American Standard Times Square Deck- Mount Bathtub Faucet with Personal Shower
- PromenAid Handrail System
-
Resting Intervals on Trails
No significant difference in vertical alignment between the trail tread, turning space, and resting interval is allowed where they meet....
-
Location
Source: NCHRP Web Only Document 117-A, Accessible Pedestrian Signals: A Guide to Best Practice, Figure 6-8 Figure 4: Installation of APS on two separated poles, aligned with crosswalk...
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....