Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
Search Results "Maximum Dimension"
-
C101.3 Conventional Industry Tolerances
-
Introduction
First, as defined in Section 104.1.1 and clarified in its advisory, they are intended to apply only to certain sections of the 2010 ADA Standards where dimensions are stated as single dimensions...
-
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This section would provide that dimensions are subject to conventional industry tolerances except where dimensions...
-
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis)
Where the turning space is constrained on two or more sides, the turning space must be 1.2 meters (4 feet) minimum by 1.5 meters (5 feet) minimum, with the 1.5 meters (5 feet) dimension...
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
Grab Bars and Handrails [4.26.2] Use of a grab bar or handrail requires the formation of a power grip so that thumb and fingers can be opposed and the surface of the palm can be in maximum...
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points.18 In practical terms, because...
-
5.8.2.1 Height of Breast Platform at Time of Measurement
Industry started with this dimension and determined the proportionate height of the breast platform to be 34 inches....
-
Knee & Toe Space [M303.2.4]
By defining the height of the breast platform as the “set point” for the other dimensions, all clearances have a static measurement point that assures maximum clearances during operation...
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.2.2
Section 608.2.2 covers the current ADA Standards for the size of standard roll-in type shower compartments.
-
SETTLEMENT AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND PALACE SPORTS AND ENTERTAINMENT, LLC, REGARDING THE PALACE OF AUBURN HILLS
[See subsections ...]
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
Clear Floor or Ground Space: ADA Standard Section 1008.4.2
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
Transfer Space: ADA Standard Section 1008.3.1.3
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.2.3
Section 608.2.3 covers the current ADA Standards for the size and clearances of alternate roll-in type shower compartments.
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
Calculation of Percentages: ADA Standard Section 104.2
Section 104.2 of the ADA Standards covers the most current information on the calculation of percentages in the ADA Standards.
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
Shape and Diameter
Use of a handrail requires the formation of a power grip so that hands and fingers can be opposed and the surface of the palm can be in maximum contact with the rail surface....
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This proposed section, which has a parallel provision in the proposed 508 Standards (E101.3), would provide that dimensions...