Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
Search Results "Maximum Dimension"
-
4.1.6(4)(a)
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
1. Thigh Breadth
Thigh breadth for this analysis was computed as the larger of two dimensions, the horizontal distance between the lateral (outer) aspect of the hips, and the horizontal distance between...
-
604.2 Location
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
Size: ADA Standard Section 407.4.6.2.1
Section 407.4.6.2.1 covers the current ADA Standards for the size of the elevator car control buttons.
-
Clearance in Base (M301.4.1 and M302.4.1)
Equipment components are permitted to be located within 8 inches maximum of the centerline of the clearance width. Question 25....
-
11B-407.2.1.2 Size and shape
Call buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
11B-407.2.1.2 Size and shape
Call buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
A. Measuring Slope and Cross Slope
Now, take the tape measure and measure the open gap at the downhill end of the level, as shown in the photo opposite - this the "critical dimension"....
-
Size: ADA Standard Section 409.4.6.1
Section 409.4.6.1 covers the current ADA Standards for the size of the car controls in private residence elevators.
-
Call Buttons: ADA Standard Section 409.2
Section 409.2 covers the current ADA Standards for call buttons in private residence elevators.
-
Controls
Controls Push buttons or plates and switches are subject to relevant requirements for controls and operating mechanisms, including the maximum 5 Ib operating force....
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309....
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309....
-
Introduction
Four static body dimensions considered relevant to the width and depth dimensions of a seating surface were computed and analyzed to serve as a reference....
-
611 Washing Machines and Clothes Dryers
The proposed rule required the door of top loading machines and the door opening of front loading machines to be 34 inches maximum above the floor (611.4)....
-
11B-812.10.4 Location
circulation path is not provided adjacent to the head end of the vehicle space or access aisle, the EV charger may be located within the projected width of the access aisle 36 inches (914 mm) maximum...
-
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment The Committee recommends a maximum distance of 1 1/2 inches from the transfer surface to the...
-
Size: ADA Standard Section 407.2.1.2
Section 407.2.1.2 covers the current ADA Standards for the size of the elevator call controls.
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....