that impairs sensory, manual or speaking skills, the test results accurately reflect the skills, aptitude, or whatever other factor of the applicant or employee that the test purports to measure...
Search Results "Mitigating Measures"
-
1630.11 Administration of tests
-
M302.4.1 Clearance in Base
The base of the diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum...
-
M301.4.1 Clearance in Base
The base of diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
M302.4.1 Clearance in Base
The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
M301.4.1 Clearance in Base
The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
Why are detectable warnings no longer required for all curb ramps or at hazardous vehicular areas?
At facilities located on sites, various measures can help reduce hazards, including reduced traffic speeds, marked crossings with pedestrian right-of-way, and speed-bumps, and other optional...
-
II-4.3300 Nondiscrimination in selection criteria and the administration of tests
required to ensure that, where necessary to avoid discrimination, employment tests are modified so that the test results reflect job skills or aptitude or whatever the test purports to measure...
-
11B-813.2.1.2 Clearance
At both ends of adult changing tables, clearance shall be provided measuring 36 inches (914 mm) minimum wide and a minimum length as long as the table width plus the width of the side clearance...
-
What Testing Accommodations Must Be Provided?
entities must ensure that the test scores of individuals with disabilities accurately reflect the individual’s aptitude or achievement level or whatever skill the exam or test is intended to measure...
-
a. Tests and Examinations
Tests and Examinations Accommodations may be needed to assure that tests or examinations measure the actual ability of an individual to perform job functions, rather than reflecting limitations...
-
CONTENTS
Providers Benefits and Costs: Overview Cost of Equipment Costs to Lower Minimum Table Height Scoping Scenarios: Range of Possibilities Benefits and Costs: Summary How to Measure...
-
Notes:
Given the differing shapes of mammography devices, defining the dimensions in relationship to each other with a static measurement point for the breast platform assures accessibility despite...
-
Test Procedures
Maximum g levels and head injury criteria (HIC) were measured....
-
Notes
in the official National Formulary, or the United States Pharmacopeia, or any supplement to them, (2) intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation...
-
Boating facilities. (Section-by-Section Analysis)
., with respect to boat slips and gangways) mitigate the burden on existing facilities?...
-
Boating facilities. (Section-by-Section Analysis)
., with respect to boat slips and gangways) mitigate the burden on existing facilities?...
-
II-2.8000 Qualified individual with a disability
duration, and severity of the risk; 2) The probability that the potential injury will actually occur; and, 3) Whether reasonable modifications of policies, practices, or procedures will mitigate...
-
Doorbell Factory Medium Rectangle Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted stainless steel push button and mounting screws Measures 2" W X 4" H Usually ships in 1-3 business...
-
R&D Workshop Trim-A-Slab Intro Video
Watch the videos in this series for detailed information on planning, measuring, and installing Trim-A-Slab, the easiest to install of any expansion joint repair....
-
D. Election Day Compliance Review
In the materials provided to each Chief Election Official for Election Day, the City will include a checklist of the temporary measures to be implemented on Election Day at each polling...
-
Back Support: ADA Standard Section 903.4
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
-
11B-406.5.12 Detectable warnings
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured...
