that impairs sensory, manual, or speaking skills, the test results accurately reflect the applicant's or employee's job skills, aptitude, or whatever other factor the test purports to measure...
Search Results "Mitigating Measures"
-
§8.12(b)
-
11B-405.3 Cross slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run). Advisory 11B-405.3 Cross slope....
-
C102.8.2 TIA 1083
Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, (March 2007), IBR proposed for Section 410.4.2....
-
1018.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
4.34.6.5(1)
(1) The sink and surrounding counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable...
-
11B-405.3 Cross slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run). Advisory 11B-405.3 Cross slope....
-
11B-405.3 Cross slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run). ◼ Advisory 11B-405.3 Cross slope....
-
Exterior Features
Accessible route to all doors Radon mitigation...
-
11B-101.2 Reserved.
These measures include, for example, installing an entrance ramp, widening entrances, and providing accessible parking spaces. 2) Second, a public accommodation should take measures...
-
11B-101.2 Reserved.
These measures include, for example, installing an entrance ramp, widening entrances, and providing accessible parking spaces. 2) Second, a public accommodation should take measures...
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
1018.5 Obstacles
Obstacles on beach access routes and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
1018.5 Obstacles
Obstacles on beach access routes and resting intervals shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191 Bus boarding and alighting areas shall provide a clear length of 96 inches (2440 mm), measured perpendicular...
-
2.4.2 Considerations of Manufacturers in Accessible MDE Design
MDE manufacturers believe that their usability requirements should include some measure of accessibility....
-
Schumacher Elevator Company: Virtual Plant Tour in HD by SAPTV
They are located in a small town in Denver, Iowa where the corn grows tall and the snow measures deep....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
M301.4.2 Clearance Around Base
The base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
12112(b)(7)
impairs sensory, manual, or speaking skills, such test results accurately reflect the skills, aptitude, or whatever other factor of such applicant or employee that such test purports to measure...
