Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
1013.4 Height
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
Doorbell Factory Round Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted stainless steel push button and mounting screws Measures 2 3/4" round Usually ships in 1-3 business...
-
Seating Locations
Remember, when measuring the accessible route through the space, measure the aisle width as if the chairs are pulled out and occupied....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
13 [§ 4.7.10]
When taking this measurement, the measuring tape should be aligned parallel to the ramp run itself and should stretch from the intersection of the ramp and gutter to the innermost edge of...
-
M304.2.1 Slip Resistant (Section-by-Section Analysis)
One manufacturer commented on this requirement, requesting that the rule provide clarification on how to define or measure a standing surface as “slip resistant.”...
-
1012.2 Height
Guards shall form a protective barrier not less than 42 inches (1067 mm) high, measured vertically above the leading edge of the tread, adjacent walking surface or adjacent seatboard....
-
E102.8 TIA (Section-by-Section Analysis)
TIA 1083 (2007), Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, would be incorporated by reference at 410.4.2....
-
C102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
10.2.1(1)
new bus stop pads are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96 inches (measured...
-
E102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
4. Summary of Practice
4.1 This practice was developed specifically for estimating pathway roughness from longitudinal profile measurements. 4.2 Longitudinal profile measurements for one wheel track are transformed...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
School Districts' Standards and Procedures
Specifically, the evaluation standards and procedures must ensure that: Evaluations consist of more than IQ tests;55 Evaluations measure specific areas of educational need...
-
Data Analysis
A repeated measures analysis of variance (ANOVA) statistical test was used to evaluate the effects of adding grab bars and a backrest to the station with regards to the maximum and minimum...
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
Completing the Checklist
If the measurement or number falls short of that required for accessibility, write the measurement or number to the right of the question in the area under “Comments.”...
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
11B-604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat....
-
5.1.2 Transfer Surface High Height
The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
